Answered: Which of the following does not belong…

Which of the following does not belong to the group? Select the corect response. Proportional limit Elastic range Yield point Elastic limit

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: why is P positive for stress A

A: The compressive stress is considered as positive and tensile stress is considered as negative.

Q: A 300 mm Long copper wire of uniform cross-section is pulled in tension so that a maximum tensile…

A: Given data : Length of copper wire = 300 mm Max. tensile stress = 270 MPa The elastic modulus of…

Q: A gold attached to a silicon wafer behaves like a cantilever beam subjected to a uniform load (see…

Q: Table 1 shows the stress-strain data for a new polymeric material rod subjected to an axial load.…

A: Table shows the stress strain data for a new polymeric material rod subjected to an axial load .Now…

Q: B. C E Strain FIGURE Q1 (a) Stress -

Q: The rigid bar ABC as shown in the figure is pinned supported at B and attached to the vertical two…

A: Length of steel rod, Coefficient of thermal expansion, Change in temperature, To find: Deformation…

Q: . An element whose material has Sy = 280 MPa, Sut= 330 MPa, and Suc= 460 MPa is loaded as shown.…

Q: Question 1. Determine the degree of indeterminacy of the below structures: (a) (b) pin (d)

Q: A plastic rod AB of length L = 0.5 m has a diameter d1 = 30 mm (see figure). A plastic sleeve CD of…

A: Given:- L = 0.5 m diameter d1 = 30 mm CD of length c = 0.3 m outer diameter d2 = 45 mm E1 =…

Q: Find the strain Change in length =0.04 mm Initial length=1000 mm

Q: At room temperature (200C) a 0.50mm gap exists between the ends of the rods shown. At a later time…

Q: A cantilever graphene column has a stress-strain relationship shown in Eqn.1. The section of the…

Q: The value of strain if stress is 35 MPa and Youngs modulus 65 MPа

A: The given question is related with solid mechanics . In this question we are provided with value of…

Q: The brass shell (ab = 20.9 × 10-6/°C) is fully bonded to the steel core (as = 11.7 × 10-6°C).…

A: Step 1:Step 2:

Q: Stress-strain behavior of a ductile and a brittle material is given in below. Which material absorbs…

A: Brief concept introduction- Ductile & Brittle materials- Without breaking, ductile materials…

Q: increased by 10°C. If the coefficient of thermal A metal bar of length 100 mm is inserted between…

A: Given data : Coefficient of thermal expansion (α)=12×10-6 per ∘CYoungs Modulus (E)=2×105…

Q: eurie the formula) d= M K wher, M- momint Ka d,

Q: i. The modulus of elasticity of a metal alloy A is 260 GPa. Compute the specific surface energy if…

A: Given : E = 260000 MPa Stress = 63 MPa crack length = 0.4 mm

Q: Determine the value of strain Change in length of rod%3D0.02 mm Initial length of rod=1000 mm

Q: A cantilever graphene column has a stress-strain relationship shown in Eqn.1. The section of the…

Q: Find the stress in each material 600 mm 400 mm 300 mm Bronze Aluminum Steel 120 kN 50 kN A mm 2400…

Q: TRUE STRESS STRAIN CUI

A: A stress-strain curve for a material is used in engineering and materials science to show the…

Q: show solution of: A liquid compressed in a container has a volume of 1 liter at a pressure of 1 MPa…

Q: The thin square plate shown is uniformly deformed such that E - +1425 µE, E, - -668 uE, and ygy -…

Q: In the strain hardening regi happens if the stress is reme

Q: b) Figure Q1 shows ceramic specimens subjected to the pure uniaxial force. Specimen A is compressed…

A: An elemental area can be subjected to stress due to applied load . For uniaxial it is subjected to…

Q: A metallic specimen is subjected to a bending moment M and an axial load F, as shown in the figure…

A: Solution- Solution:The configuration is shown below, ∵ For the null condition , AB=CDThe output pc…

Q: The ratio of direct stress to the limit. The ratio is known as Volumetric strain O Bulk modulus O…

A: The ratio of direct stress to volumetric strain within elastic limit is called BULK MODULUS.

Q: Show the typical Stress versus Strain curve for the following materials, and define the materials…

A: Polypropylene is a thermoplastic resin that has an excellent stiffness and chemical resistance, a…

Q: Creep exercises You are involved in a design for high temperature alloys and have performed a…

A: Solution:- Give data:- To know:- Selection of material as shown in above figure.

Q: The rigid bar is supported by a pin at A and two metal wires, each having a diameter of 4 mm. The…

Q: Stresses that cause change in volume are called (A) hydrostatic stresses B deviatoric stresses…

A: We need to choose correct option based on given choices

Q: A structural component in a fighter jet aircraft has a cellular cross-section (Fig. Q1). The…

A: Given,Torsional load, T = 40 Nm = 40×103 NmmModulus of rigidity, G = 30 GPa = 30×103 MPa = 30×103…

Q: Calculate Young's modulus for an iron crystal when tension is applied along [2 -2 1] direction.…

A: S11 = 7.6(TPa)-1 S12 = 2.8(TPa)-1 S44 = 8.6(TPa)-1

Q: Draw a tensile stress-strain curve for a typical semi-crystalline polymer such as LLDPE, and define…

Q: The ratio of direct stress to volumetric strain in case of a body subjected to three mutually…

A: The ratio of direct stress to volumetric strain in case of body subjected to three mutually…

Q: Tim In the yielding region, what happens if the stress is removed? O a. The material does not return…

Question

Which of the following does not belong to the group?
Select the corect response.
Proportional limit
Elastic range
Yield point
S Blastic limit

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

If the posson ratio of elastic material is 0.453 the ratio of modulus of rigidity to Young modulus
For the structure shown with loading symbolised as (1) and (2), what is the stiffness matrix?
Which of the following is false regarding factor of safety in the design of structures? a. It considers uncertainties in the material properties. b. A higher factor of safety is preferable in designing safe structures c. It should not be less than 1 to ensure the structure’s safety. d. It considers changes in the loading pattern on the structure. Which of the following occurs when the value of Poisson’s ratio is doubled and the modulus of elasticity is kept constant? a. The lateral deformations experienced by the material is halved b. The volume of the material will remain constant when subjected to external forces c. The elastic region of the shear stress-strain diagram would be less steep d. The material can withstand higher amounts of stress before permanent deformations occur
The Young's modulus of elasticity of a material is 2.5 times its modulus of rigidity. The Posson's ratio for the material will be: (c) 0.50 [IAS-1997] (a) 0.25 (b) 0.33 (d) 0.75
The rigid horizontal bar ABC of negligible mass is connected to two rods as shown in the figure. If the system is initially stress-free, calculate the temperature change that will cause a tensile stress of 90 MPa in the brass rod. Assume that both rods are subjected to the same change in temperature.
Fast plzz
What is the change in dia.
1 It is the ratio of ultimate tensile stress to the permissible stress. Plastic Shear Plastic limit Proportional limit Factor of safety Poisson's ratio
The material returns to its original shape when the load is removed. (A Elastic Limit B Elastic Behavior Limit c) Maximum Limit D D Proportional Limit
19 This theory explains that the elastic failure occurs when energy per unit volume in a strained material reaches the value of the strain energy per unit volume at the elastic limit point in the simple tension test. Also, the maximum energy which a body can store without deforming plastically is constant for that material irrespective of the manner of loading. What do you call this theory Bulk Modulus Volumetric strain Hook's Law Elastic Theory Strain energy theory
1. At a temperature of 5°C, a 3-mm gap exists between the end of polymer bar (1) and support A as shown. Bar (1) is 50 mm wide and 20 mm thick (E = 800 MPa, a = 140 x 10-6/°C). Bar (2) is 75 mm wide and 25 mm thick (E = 2.7 GPa, a = 67 x 106/°C). The supports at A and C are rigid (i.e., fixed). Determine: a) the temperature at which the normal stress in bar (2) will be equal to -3.0 MPa, and b) the lengths of the two polymer bars at this temperature. (1) 3-mm gap 50 mm 500 mm B 75 mm 400 mm (2)
11) In the figure shown, the------- (a) Adhesion > Cohesion (b) Cohesion> Adhesion