In an industry, the water in a boiler tank needs to be kept at constant pressure, water to the tank comes at constant flow rate and steam is coming from a valve to maintain the pressure. A pressure gauge is used to measure the water pressure in the tank. Provide the block diagram representation using a PID controller for the above mentioned condition (Control the pressure using the proportional valve.). a. explain the working principle.

In an industry, the water in a boiler tank needs to be kept at constant pressure, water to the tank comes at constant flow rate and steam is coming from a valve to maintain the pressure. A pressure gauge is used to measure the water pressure in the tank. Provide the block diagram representation using a PID controller for the above mentioned condition (Control the pressure using the proportional valve.). a. explain the working principle.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Make a diagram.
BOOK: FLUID POWER, 3e, JAMES A. SULLIVAN PROBLEM: 13 - 1
Explain about the close loop control of the Process (Pressure control systems) with a neat diagram.
Draw a net circuit by hand using a ruler in the grid provided sheet below. connect it in the right way.
Task Page Static Temperature (mixture) line-19 Run Calculation 2.72e+02 Check Case... Preview Mesh Motion... Time Advancement Туре Method 2.71e+02 Fixed User-Specified Parameters 2.70e+02 F Line/Rake Surface Name line-19 Static 2.69e+02 Options Number of Points Temperature (mixture) O Line Туре 10 Line Reset 2.68e+02 (k) End Points x0 (m) 0 x1 (m) 0.032 2.67e+02 yo (m) 0.04 y1 (m) 0.04 z0 (m) z1 (m) 0 Select Points with Mouse 2.66e+02 0.005 0.01 0.015 0.02 0.025 0.03 0.035 Save Close Help Position (m) Calculate |-Q|Q | R - O selected
quick pls
Perform a simple mass balance on the completely mixed reactor below to identify the recycled sludge concentration, X, as a -- I -- function of the recycle ratio, R, and the mixed liquor concentration, x. Draw the system control boundary across which your mass balance is performed. a. b, Set-up your mass balance equation. Make sure to clearly identify inflows, outflows, rates of growth/consumption, etc., within your system; Identify ALL assumptions; c. d. e. Solve your mass balance equation for the recycle sludge concentration; If your recycle ratio, R, is 45% and your wasting rate is 5% of the average daily flow, what is the expected recycle sludge concentration, X, with respect to the mixed liquor concentration, X? Influent Effluent Clarifier WAS RAS Completely mixed reactor system
Select a car automatic speed (cruising speed) control system as a process. The overall controlling process hava a fuel control unit/valve, controller, and other instruments to act as an automatic feed back speed control system. Draw a complete block diagaram for this specific speed control proces, name the components and explain the process briefly.
Q. Blood flow. An artery of diameter 1.0 cm divides completely into capillaries, each of diameter 20 microns. There are a large number of capillaries, N, such that the net cross sectional area for these capillaries is equal to the cross sectional area of the artery. What is AP:/APa, the ratio of the pressure change per unit length along one of the capillaries (AP) to that of the pressure change per unit length along the artery (APa)? O2.5 x105 O1.0 O4.0 x10-6 5.0 x102 12 x108 O 6.2 x1010 Page 10 of 1
b) A pitot tube flow sensor is used to measure the flow rate in a pipe, as shown in Figure Q4. Impact Probe P1 Direction of Flow Static Probe P2 Differential pressure transducer Figure Q4 A manometer is used to measure the differential pressure, showing a difference in fluid level of 150 mm between the two probes. Calculate the differential pressure if the liquid has a density of 900 kg / m3, expressing your answer in pascals and also bar. (Gravitational acceleration, g may be taken as 9.81 m/s².) (Question 4 continues on the next page.) Page 5 of 14 (Question 4 continues below.) c) The velocity of the fluid is given by: 2(P1-P2) V = (m/s) where P1 - P2 is the differential pressure, measured in Pascals. Calculate the linear flow rate in m/s. d) If the diameter of the pipe is 200 mm, calculate the i) volumetric flow rate in m3/s ii) mass flow rate in kg/s
Provided is A, B, C. I only need d to finish.