According to the circuit shown below answer the following two questions:       B) Reconnect the input switches (s1, s2, P.B.1, P.B.2) in a deferent method to satisfy:   1- The same function.   2- Restrict the speed of the cylinder in retracting stroke as meter out

Q: Evaluate the 3-DOF wrist as shown in Figure 2, use the conventional method to determine 1. Linear…

A:

Q: Write the number of limbs, determine the degrees of freedom and draw the kinematic chain.  b)…

A: As valve engine is given where we are to find 1st number of links and number of higher joints and…

Q: A slider-crank mechanism is required to do the following crank angle-slider position combinations.…

A: given position angle in degree slider position position 1 0 12 cm position 2 90 10 cm…

Q: ) The continuous stopwatch timing method was used to obtain the observed times for a worker-machine…

A:

Q: A PVC (k = 0.20 W/m-K) pipe is 2.5 m long and has inner and outer radii of 2.3 cm and 3.3 cm,…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: Question 2. la0 mm diameter siphon draws water from the reservoir. Considering that the elevation…

A: Given diameter =4mm=0.004 m h(1)=1m h(2)=1 m

Q: Table Q1 shows the initial temperature distribution of a 1 cm long steel bar at equal distance Table…

A: Given : Initial Temperature - 110, 85, 70, 55, 17 L = 1 cm Diffusivity, K = 2.5 cm2/s To find : a)…

Q: Given: N110, N2 = 20, N3 = 30, N4 = 40, J1 = 1, J2 = 2, J3 = 3, J4 = 4, J5 = 5, D1 = 1, and D2 = 2.…

A: Given: To find: θsT2s

Q: Newton Raphson and False position method are bracketing method. Select one: True False

A: The open methods are - Newton Raphson Secant Method Bracketing Methods- Bisection Method False…

Q: serve the motion of the block and statements accurately describes displacement was 10 cm.…

A:

Q: While constructing a building, an engineer need to fix two steel beams together using a bracket as…

A:

Q: Direction:  •Show unit cancellations and do not use shift solve. •Show your complete solution with…

A:

Q: 1. Given a four-bar linkage with the link lengths Li = d = 100 mm, L2 = a = 40 mm, L3 = b = 120 mm,…

A: Given data L1=R1=d=100mm L2=R2=a=40mm L3=R=b=120mm L4=R4=c=80mm theta 2 = 100 degrees. 1. Scale used…

Q: For a given pump, the flow rate and net heads are given in the table. Six of these pumps are…

A: It is asked to plot the system curves and pump curves for the given pump configuration

Q: R Problem Statement: A car drives on a circular track with radius 270 m. Initially, the displacement…

A: Given: The radius of circular track, R = 270 m The initial displacement, so = 0 The initial speed, v…

Q: The rate of heat flow (conduction) between two points on a cylinder heated at one end is given by…

A:

Q: 5. You need to know the resolution of the control. How many counts are there for 1 degree of motion?

A: Solution:

Q: The control system employs microcontroller to control the variables then it is called as direct…

A:

Q: Find the values of rise time (tr), peak time(tp), settling time(ts) and maximum value from the…

A: Please refer the following figure for the rise time (tr), peak time (tp), settling time (ts) and…

Q: use the seize-and-fix methodology to determine the degrees of freedom of the following system

A:

Q: 1. Passengers in the jet transport A flying east at a speed of 800 km/h observe a second jet plane B…

A:

Q: Respond with TRUE if the symbol of the valve shown below is drawn correctly. 9ype here to search Say…

A: Ans- True

Q: The location of the tool, WT, is not accurately known. Using force control, the robot feels around…

A: Given:coordinate systemsfind:The transform equation

Q: 50 kg Mạ - 3 ft- - 3 ft | 200 lb · ft Collar 4 ft B 12 Smooth surface Fig 1

A: Given-Data:-  Force=50kg=110.231lb To-Find:- Reactions on the bent rod

Q: The figure shows a linkage in one position. What is the instantaneous acceleration of point Pif the…

A:

Q: e 3 al Views xiliary View 75 TOP VIEW 1₂ 26 26 PLAT SLOTTED SCALE

A: GIven

Q: Plot the response of the system shown above for the following conditions: a. There is no damper b.…

A: Given : To find : Response plot of the system

Q: Question 1: The crank O1A of a mechanism as shown in figure below rotates uniformly at 955 rpm…

A: 01A =0.1mV01A = VA= 10m/secNow let us locate the required instantneous center :-No. of Instantenous…

Q: Newton-Euler method and Lagrangian-Euler method will give different equations of motions for the…

A: TRUE  both the methods gives different equation of motions for same manipulator

Q: b) You are given a set of six links. The lengths of the links are as follows: 6.3cm,…

A:

Q: For the given multiview projection, draw the corresponding isometric drawing. # maka ㅏ

A: For the given multi view projection, draw the corresponding isometric drawing.

Q: Manipulated variable is the variable which is used to maintain the output at setpoint. Select one:…

A: Manipulated variable is the variable which is used to maintain the output at setpoint. Answer: True

Q: Water from a hose is being discharged straight vertically upwards until a height of 32 ft. What is…

A:

Laws of thermodynamics

Thermodynamics is a field of research, which needs the creation of absolute and ideal states and logical and practical examination of the actual conditions. By considering all the laws and theories of thermodynamics, the chemical reactions, the occurrence of processes, and physiological functions can be predicted with this field.