1. Given a four-bar linkage with the link lengths L1 = d = 100 mm, L2 = a = 40 mm, L3 = b = 120 mm,L4 =c= 80 mm. For 0 = 60°, m2 = 5 rad/s (CCW), RCA=110 mm and 83 = 30°, find 03, 04, VĄ, V B, V cfor open circuit bya) Graphical methodb) Instant center methodc) Vector loop method.Then compare the obtained results.

Given data L1=R1=d=100mm L2=R2=a=40mm L3=R=b=120mm L4=R4=c=80mm theta 2 = 100 degrees. 1. Scale used…

1. Given a four-bar linkage with the link lengths Li = d = 100 mm, L2 = a = 40 mm, L3 = b = 120 mm, L4 =c= 80 mm. For 02 = 60°, w2 = 5 rad/s (CCW), RCA=110 mm and &3= 30°, find m3, 04, V a, V B, V c for open circuit by a) Graphical method b) Instant center method c) Vector loop method. Then compare the obtained results.

1. Given a four-bar linkage with the link lengths Li = d = 100 mm, L2 = a = 40 mm, L3 = b = 120 mm, L4 =c= 80 mm. For 02 = 60°, w2 = 5 rad/s (CCW), RCA=110 mm and &3= 30°, find m3, 04, V a, V B, V c for open circuit by a) Graphical method b) Instant center method c) Vector loop method. Then compare the obtained results.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

8.) тм 1. 8.) The linkage below: link I is ground, AB is link 2 is @ what point? BC is link 3 slider is link 4 I E D ULET ALL F rauau u A B с D E F Wen 1014
A four-bar linkage with r = 50 mm, r2 = 60 mm, r3 = 80 mm, r= 100 mm and 0 = 0". %3D Y4 Figure Q4 Compute; a) the corresponding values of 0s and 0, for each link when the driving crank is in the positions of 0 = 20° counter clockwise, b) the velocity at point A,VA when the driving crank is in the angular velocity of ox = 20 rad/sec.
A four-bar mechanism is used to transmit power to slider E. Link AC rotates counterclockwise at 100 rpm. A and B are fixed points. The following linkages are measured in cm: AC=35, AB=70, CD=45, BD=45, DE=40. Find the instantaneous velocity of slider E in cm/s 1.Draw the mechanism in appropriate scale on your paper2. Find the instantaneous linear velocity of C3. Find a point on your paper to draw the velocity polygon and scale the magnitude of the computed linearvelocity4. Use the relative velocity equation for finding the linearvelocity of D; ? = ? + ?? ? ?/?5. Remember that although the magnitudes are unknown, their directions can be identified6. Obtain the magnitudes of the unknown velocities from the velocity polygon7. For Link DE, repeat the process by using ? = ? + ??the line as much as needed8. Remember that E is a SLIDER therefore it can only goin the direction where its movement is not constrained? . Add the vector ? to the head of ? and extend?/? ?/??
The ratio of output to input of a system is known as Transfer function. Select one: O True O False Coloct the cinmple cuctom fcom the fellouuing
M7
Q1. A mechanical system is shown in the following figure, where external force u₁ is the input and displacement y₂ is the output. The force acting on m₂ has a linear relationship with u₁ as u₂-Au₁. • List system equations and do Laplace transform to the system equations; • Draw block diagram of the control system. (Please construct the block diagram from system equations directly, do not derive or combine the equations. Do not need to reduce it) YI Y b₁ m₁ 11 112 + m₂ www
Draw the corresponding scheme and find the equation on the right. Method used and Four assumptions hA Tc.v.(t) = Taire + [Tc.v.(tt) – Tairele locp)"
write Design spsecifcation for this system in small paragraphs
Write a method and steps in which we derived reverse kinematic equations ??
The linkage in the following figure has O2A = 0.8, AB = 1.93, AC = 1.33, and offset = 0.38 in. The crank angle in the position shown is 34.3° and angle BAC = 38.6°. Find a 3, A4, Ag and Ac for the position shown for 02 = 15 rad/s, a2= 10 rad/sec² in direction shown. 5. a) Using the acceleration difference graphical method b) Using an analytical method. A 3 B 02 4 1
write vector loop equation(s) theta2=57 also if a new length is constructed find its value. 02 57° 30° X L₁= 162 L2=40 L4=122 L3=96 0₁