In a sudden enlargement of a pipe cross-section, if the velocity of flow at the inlet of pipe (V1) = 40 m/s, velocity of flow at the outlet of the pipe (V2) = 20 m/s and the acceleration due to gravity is assumed to be 10 m/s2, then the loss of head due to sudden enlargement of pipe is: a. 18 m of water b. 40 m of water c. 15 m of water d. 20 m of water

In a sudden enlargement of a pipe cross-section, if the velocity of flow at the inlet of pipe (V1) = 40 m/s, velocity of flow at the outlet of the pipe (V2) = 20 m/s and the acceleration due to gravity is assumed to be 10 m/s2, then the loss of head due to sudden enlargement of pipe is: a. 18 m of water b. 40 m of water c. 15 m of water d. 20 m of water

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2xy, v = x² – y², is irrotational and incompressible, and determine its stream function and velocity potential p. 2. Demonstrate that the two-dimensional flow fluid flow defined by u =
A rectangular tank 3 m x 4 m is 5 m high with 2 orifices placed at a vertical distances of 0.5 m and 1m from the bottom respectively. Both orifices are 100 mm diameter with C=0.607. Determine the: show complete solution a. How long will it take to lower the water at tank by 2 m in seconds?b. How long will it take for the water surface to be at the same level as the upper orifice in seconds?
L = 900m D=35cm L=600m L=900m D=75cm D=60cm L=600m D=30cm L=900m D=40cm A flow rate of 0.5 m³/s is branched into three pipes and then rejoined in the concrete parallel pipes as shown in the figure below. Find the head of loss between point A and point B. Here, the coefficient of friction loss in all tubes is 0.03.
Consider a flow of SAE 30W oil through a 12-cm-diameter pipe. For SAE 30W oil, take p=891kg/m³. u= 0.29 kg/m-s at 20 °C, and μ = 0.01 kg/m-s at 100 °C, and π = 22/7. 4. For what flow rate in m³/h would a transition to turbulence take place at 100°C? Round the answer to one decimal place. The flow rate is m³/h.
Two pipes A and B are connected in parallel between two points M and N as shown in figure. Pipe A is 80 mm diameter, 900 m long and its friction factor is 0.015. Pipe B is of 100 mm diameter, 700 m long and its friction factor is 0.018. A total discharge of 0.030 m³/s is entering the parallel pipes through the division at M. Calculate the discharge in the two pipes A and B. M = 0.015 A fA 80 mm dia, 900 m 100 mm dia, 700 m B fB = = 0.018 N
The flow rate of water flowing out of an 80mm diameter nozzle shown in Figure 1 is60 litre/s. The volume of the water in the pipe bend is 50 litres and the pipe bend isinstalled in a vertical plane. The head loss from point 1 to 2 is 0.44m. Calculate the xand y for components of the thrust block to hold the pipe bend.
Mato 5
A duct of diameter 0.8 m carries gas (p = 1.3 kg/m³). At one point, the duct diameter reduces to 0.74 m. Starting from Bernoulli's equation, estimate the velocity of flow in the reduced section, and the mass flow rate (=pQ) through the duct if the pressure difference between a point upstream of the reduction and another point at the reduction is equivalent to 30 mm of water.