Talk N Textall al aO N 89I 1l:48TNTFinal Assignment_Rigid Bo...I.GENERAL INSTRUCTIONS1. Do this BY PAIR or individually. Write your name/s. Submit thisonly once.2. Draw the figure to illustrate your understanding of the problem(as required).3. Show complete formulas and solutions.4. No rounding off in the solutions, only your final answer should berounded off to 3 decimal places. In cases where the answer in asub question will be used for the following sub question, use thenon-rounded value.5. Enclose your final answer in a box. No extra answers.6. File submissions should be in single PDF.7. Once you submit your solution papers late, your score willautomatically be reduced by half, regardless of how late you are(1 min or more).Presentation matters.II. ProblemsProblem 1Given:Mass of canister: 4000 kgMass of beam BD: 50 kgMax allowable force:1. AB =2. CD = 30 kN30 kN3. EF =34 kN4. GH = 34 kNDetermine the greatest allowable acceleration of the system.Problem 2Given:075 m 64.Mass of car:1400 kgIDMass of trailer: see kg2m 1.5 m2 m1.25 mBraking force at C (pe e.4e) is applied and causes skid.PING,0.75 m0.4 mFREE TOROLL·FREE TOROLLIm- 2 m+1.5 m 2 m 1.25 mDetermine the reactions at B, C, and D.Note: Pin supports can resist both vertical and hortzontal forces.

Answered: Image /qna-images/answer/d778999f-df09-4886-80ee-1f5e195d61af.jpg

II. Problems Problem 1 Given: Mass of canister: 4000 kg Mass of beam BD: 50 kg Max allowable force: 1. AB - 30 kN 2. CD - 30 kN 3. EF - 34 kN 4. GH - 34 kN Determine the greatest allowable acceleration of the system.

II. Problems Problem 1 Given: Mass of canister: 4000 kg Mass of beam BD: 50 kg Max allowable force: 1. AB - 30 kN 2. CD - 30 kN 3. EF - 34 kN 4. GH - 34 kN Determine the greatest allowable acceleration of the system.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

B9
Within few minutes
The bridge shown in Figure consists of two end sections, each weighing 20 tons with center of gravity at G, hinged to a uniform center span weighing 12 tons. Compute the Reaction at B. * 6 tons -40m- 20m 40m -30m20m-20m- -60m- -20m20m30m- None of the above 26 tons O 4.8 tons O 4 tons O 23.2 tons B.
Determine and explain thoroughly, a. the equations of the shear and bending moment curves for the beam and loading shown in the diagram. b. draw the shear and bending moment curves for the beam and loading shown c. the maximum absolute value of the shear and bending moment.(Show the solution). 24 kN 29 kN/m В A D 300 -3 m 2 m 1 m
Determine the design moment capacity of the reinforced concrete beam shown inFigure 1(a) if it is reinforced with 4-28-mm diameter in tension and 2- 16-mmdiameter in compression.
6.12 ft L D G_4.24 ft F C 0.88 R K T 12.12 + 1 LT-- A 45° j4 ft K ftl 4.24 ft Referring to the figure shown. Determine the horizontal force due to the water acting on the cylinder per foot of its length.
Provide complete solution with explanation solution must be handwritten will give like if instructions followed
Compute the reactions and the end moments for the frame shown below. 4.9 kN/m 6 kN B 4 m, El 3 m, 2EI FEMA -4 H Good luck Dr. Ali Sadeghpour L 4 m, El D FEM 3 m, 2El 4 m, El E **
Homework 14 |A cylindrical vessel closed at the top and bo om is 300mm inn diameter, 1m long and contains water up to a depth of 0.8m. The air above the water surface is at a pressure of 60 KPa. If the vessel is rotated at a speed of 250n rpm about its ver cal axis, nd the pressure head at the bo om of the vessel at the center point and at the edge.
2. The 50 kg uniform crate initially rests on the inclined surface. If a force (F-40t +200 N) as shown in the figure below starts to pull the crate, determine the power output develop by the force at t-6 s. The coefficients of static and kinetic friction between the crate and the surface are s-0.20 and Hk-0.15. F-40t+200 N F (r in second) 30°
Locate the position o maximum deflection. What is the deflection at 2 meters from the left? Concentrated Load = 350N, Triangular Load = 1700N/m Dimensions: Length = 1.0(2) = 2.0mm, Thickness = 40mm, Height = 200mm, Height - Thickness = 160mm
Q2 The truck dumps water on the ground such that it flows from the truck through a 100-mm-wide opening at an angle of 60°. The length of the opening is 2 m. Determine the friction force that all the wheels of the truck must exert on the ground to keep the truck from moving at the instant the water depth in the truck is 1.75 m. 1.75 m