Considering the effects of the prestressing forces (assume no loss) and the working loads(include the selfweight of the beam). Calculate the stress indicated below.Calculate ftop at midspan. (MPa), consider sign convention (- for compression, + fortension)5 kN/m EXCLUD In6SELFWEIGHT300 = PP=300 kNI5M400de = 24 1Nm3N.A.80070

Considering the effects of the prestressing forces (assume no lo (include the selfweight of the beam). Calculate the stress indica Calculate ftop at midspan. (MPa), consider sign convention (- fc tension)

Considering the effects of the prestressing forces (assume no lo (include the selfweight of the beam). Calculate the stress indica Calculate ftop at midspan. (MPa), consider sign convention (- fc tension)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

All forces applied in the system are in the (x - y) plane. The material point B at the top of the beam is rotated at an angle of 15° counterclockwise. It is required that the shear stress is 17.5 MPa for this rotated material point B. At the bottom point A of the beam it is required that the maximum tensile stress is 110 MPa. Determine the load P and the length d that satisfies these constraints defined for points A and B. Given data: L= 4 b, t = b / 25, c = 2b, b = 1000 mm, e = 12, f=5 b/4- q = 2P/L b/ 4 -b/4- P
A cantilever beam AB is loaded as shown in the Cross-section of the beam figure and the beam is supported with a cable BD. The beam's cross-section is rectangular as shown. It is known that the tension force in cable BD is 10.39 kN. Calculate the normal stress at point a, and calculate the shear stress at point c. Ignore the weight of the beam. 10cm 10cm +15cm+ 75cm B F-13.99KN 30cm 60cm 90cm
Since the bending safety stress σem = 10 MPa, shear safety stress Tem = 600 kPa of the rectangular section beam given the loading status in the figure and width b = 150 mm, how much should the height h of the beam section be at least so that the stresses that will occur in the beam do not exceed the safety stress values. .
Several torques are applied to the stepped shaft (G= 80 GPa) shown in Fig. 1. Neglect any Stress concentrations associated with the sudden change in cross-section. Determine: (a) The maximum shear stress in the shaft (b) The rotation of the end E relative to the end A. 500 N-m 300 N-m FC 30 mm 400 mm A C 150 N-m 300 mm 350 mm D 50 N-m E 450 mm 20 mm
Several torques are applied to the stepped shaft (G= 80 GPa) shown in Fig. 1. Neglect any Stress concentrations associated with the sudden change in cross-section. Determine: (a) The maximum shear stress in the shaft (b) The rotation of the end E relative to the end A. 500 N-m 300 N-m FC 30 mm 400 mm A C 150 N-m 300 mm 350 mm D 50 N-m E 450 mm 20 mm
The couple M=1.1 kN-m acts in a vertical plane and is applied to a beam oriented as shown. Determine the stress at point A 10 mm 40 mm The stress at point A is ( 10 mm 40 mm -10 mm 1,-1.894 x 10 mm 1,-0.614 x 10 mm +0.800 x 10 mm MPa.
Find the mayximum bending stress 75 N/m 60° N/m 2) 5m Ø Icm
Calculate the moment of Resistance of the given beams. If the maximum stress is 100 N/mm2. 190 |不 15 (i) 550 k10> (all dimensions in mm)
4.2- If positive M of 20kN.m is applied, draw the bending stress distribution. Est =200GPa and EAlu = 10GPa 180mm 20mm Wood Steel 100mm
All forces applied in the system are in the (x - y) plane. The material point B at the top of the beam is rotated at an angle of 15° counterclockwise. It is required that the shear stress is 12.5 MPa for this rotated material point B. At the bottom point A of the beam it is required that the maximum tensile stress is 110 MPa. Determine the load P and the length d that satisfies these constraints defined for points A and B. Given data: L = 4 b, t = b / 25, c = 2b, b = 600 mm, e = 5 , f = 12