Answered: 2. The magnitude of the three forces…

2. The magnitude of the three forces acting on the plate are F₁ = 100KN, F₂=80kN and F3= 50kN. Solve for the resultant completely. (R and 0, 8y, and 8₂) 1m F1 2m X 6m 3m F2 2m F3 2m y

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. The plate is acted on by four parallel forces, three of which are shown. The fourth force P and its line of action are unknown. The resultant of this force system is the couple-vector. (-1100i + 1500J)lbft. Determine P and its line of action. %D 1400 lb 200 lb 300 1b y 2. ft 3 ft 3 ft 4 ft
SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in the center section of the truss may be assumed to be capable of supporting tension only. Given: P=2.8kN 0=15⁰ a=3m b=3m c= 5m 5 panels@(a)m each F E b G B b b C a Q Zoom image Compute the force on member CL P
i need the answer quickly
Q.4) A pipe assembly is acted on by four forces and one couple moment. The 300 N force is parallel with the z-axis, the 130 N force is parallel with the y-axis, and the 60 N force is parallel with the x-axis. Force F, has a magnitude of 220 N and coordinate direction angles given by aA = 45°, BA = 60°, and YA = 120°. The couple moment M, is in the x-z plane and has a magnitude of 400 N-m. Determine the resultant moment about point B. Mc 30 300 N 1 m B0.5 m 0.75 m 0.75 m 130 N FA
A horizontal force of F = {-50i} N is appliedperpendicular to the handle of the pipe wrench. Determinethe moment that this force exerts along the axis OA (z axis)of the pipe assembly. Both the wrench and pipe assembly,OABC, lie in the y-z plane. Suggestion: Use a scalar analysis.
The T-beam is subjected to a bending moment of M = 150 kip in. directed as shown. Determine the maximum bending stress in the beam and the orientation of the neutral axis. Make sure you check all possible points (corners) for max stress and/or state other reasoning for the point that you pick. Answer: [σmax = 3.33 ksi, β = -63.1°]
SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in the center section of the truss may be assumed to be capable of supporting tension only. Given: P=2.8kN 0=15⁰ a=3m b=3m c = 5m 5 panels@(a)m each F E b B b b P G C Zoom image Compute the force induced in member AB
SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in the center section of the truss may be assumed to be capable of supporting tension only. Given: P=2.8kN 8=15⁰ a = 3m b=3m c= 5m 5 panels@(a)m each D E b G P b b K C Zoom image Compute the force induced in member CD. C B
Solve for the reactions, the deflection at free-end, and the slope at the midspan. Use E = 200 GPa and I = 50 x 106 mm4 Final Equations with value of C1 and C2 EIy'' = EIy' = EIy = RA: RB: RC: Deflection: Slope:
The steel pipe (G - 75GPA) has an outer diameter of 50mm and an inner diameter of 30mm. It is fixed at A and three torques are applied to it as shown. Solve the rotation of the free end with respect to the fixed end. 200mm 250mm 300mm 30 N-m 20 N.m 80 N-m O 0.000749rad O 0.000674rad O 0.00624rad O 0.00142rad
150 mm 60 mn 300 nm 000 m 50 mm 5 m B 25 kNm 5 m 10 KN A beam is created by nailing 3 planks together with 2 rows of nails as shown above. The beam exhibits a pin support at A and is suspended by a cable at B. A concentrated load of 10 kN is applied at the free end while a moment of 25 kNm is applied at location B. a) Determine the second moment of area (I) of the cross-section b) Draw the free body diagram, shear force diagram, and bending moment diagram of the beam c) For the maximum shear force on your SFD, determine the maximum and minimum shear stresses at the interface between the horizontal and vertical planks d) For the maximum shear force on your SFD, Determine the shear stress at the neutral axis
SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in the center section of the truss may be assumed to be capable of supporting tension only. Given: P=2.8kN 0=15⁰ a=3m b=3m c= 5m 5 panels@(a)m each F D E b G B Ө 0 P b b C Zoom image Compute the force induced in member DB. C P