૨૩:If P = 200 N and the 15-kg uniform slender rod starts fromrest at 0 = 0°, determine the rod's angular velocity at theinstant just before 0 = 45°.Ans.:@₂ = 4.97 rad/s45°600 mmP = 200 NSOC

Answered: Image /qna-images/answer/ca6d9e8e-72af-486b-8a23-fc7e770a58b8.jpg

૨૩: If P = 200 N and the 15-kg uniform slender rod starts from rest at = 0°, determine the rod's angular velocity at the instant just before 0 = 45°. Ans.: w₂ = 4.97 rad/s 45° 600 mm 01 P = 200 N

૨૩: If P = 200 N and the 15-kg uniform slender rod starts from rest at = 0°, determine the rod's angular velocity at the instant just before 0 = 45°. Ans.: w₂ = 4.97 rad/s 45° 600 mm 01 P = 200 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The ends of the 0.62-m bar remain in contact with their respective support surfaces. End B has a velocity of 0.58 m/s and an acceleration of 0.37 m/s² in the directions shown. Determine the angular acceleration a (positive if counterclockwise, negative if clockwise) of the bar and the acceleration of end A (positive if up, negative if down). 21° A 0.62 m 101° Answers: α = aA = i i Bag=0.37 m/s² UB=0.58 m/s rad/s² m/s²
The 18-kg rod AB is pin-connected at A and subjected to a couple moment of M =15 N- m The rod is released from rest when the spring is unstretched at 0 = 30°. As the rod rotates, the spring always remains horizontal, because of the roller support at C. (Figure 1) Determine the rod' s angular velocity, measured clockwise, at the instant 0 = 60°. Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwise. vec rad/s k = 40 N/m 0.75 m M = 15 N- m
Two wooden members are joined by plywood splice plates that are fully glued on the contact surfaces. Knowing that the clearance between the ends of the members is 6 mm and that the ultimate shearing stress in the glued joint is 2.5 MPa, determine the length L for which the factor of safety is 2.75 for the loading shown. Take P = 13 kN.
The outer radius of the spool is R = 0.65 m and the radius of the inner hub is r = 0.35 m. Determine the magnitude of the acceleration of point A if ao = {(0.4)i} m/s?, vo = {(1)i} m/s and the spool rolls without slipping. The answers are given in m/s?. Note that O and A are at the same height. A R
ω F A 2 kg ball with radius 9 cm and radius of gyration of 7 cm is moving to the right at 2 m/s while a 5 N force is applied, accelerating its motion. It is currently backspinning (and therefore slipping) at w = 4 rad/s, with μk = 0.3. Find the acceleration of the balls center and also the angular acceleration of the ball at this instant a = m (positive right) $2 rad απ (positive $2 CCW)
At the instant shown, the spring is un-deformed. Determine the change in potential energy if the 20 kg disk (with radius of gyration kG = 0.5 m) rolls 2 revolutions without slipping. k= 200 N/m 3 m/s datum 0.3 m M = 2 Nm 30° O 1791 J O -1791 J O 1051 J O 1421 J O E) None of the above
Pravinbhai
The racing vehicle has a mass of 750 kg and center of mass in G. If there is no slippage, determinate the normal reaction, in Newtons, presented on each of the front wheels in A, when an acceleration of a = 6.4 m/s². 250 mm TIRE A GOFF 1625 mm G 1385 mm GOFAS B