Two wooden members are joined by plywood splice plates that are fully glued on the contact surfaces. Knowing that the clearance between the ends of the members is 6 mm and that the ultimate shearing stress in the glued joint is 2.5 MPa, determine the length L for which the factor of safety is 2.75 for the loading shown. Take P = 13 kN. Two wooden members are joined by plywood splice plates that are fully glued on the contact surfaces.Knowing that the clearance between the ends of the members is 6 mm and that the ultimate shearingstress in the glued joint is 2.5 MPa, determine the length L for which the factor of safety is 2.75 for theloading shown. Take P= 13 kN.P6 mmPThe length Lis125 mmmm.

The given information in the problem is shown in the following attached image:

Two wooden members are joined by plywood splice plates that are fully glued on the contact surfaces. Knowing that the clearance between the ends of the members is 6 mm and that the ultimate shearing stress in the glued joint is 2.5 MPa, determine the length L for which the factor of safety is 2.75 for the loading shown. Take P= 13 kN. P 6 mm P The length Lis 125 mm mm.

Two wooden members are joined by plywood splice plates that are fully glued on the contact surfaces. Knowing that the clearance between the ends of the members is 6 mm and that the ultimate shearing stress in the glued joint is 2.5 MPa, determine the length L for which the factor of safety is 2.75 for the loading shown. Take P= 13 kN. P 6 mm P The length Lis 125 mm mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

19. knowing that a force P of magnitude 75 N is applied to the pedestal shown, determine (a) the diameter of the pin at C for which the average shearing stress in the pin is 40 MPa, (b) the corresponding bearing stress in the pedestal at C, (c) the corresponding bearing stress in each support bracket at C. 75 mm 9 mm 300 mm PI 125 mm D 5 mm
An annular washer distributes the load P applied to a steel rod to a timber support. The rod's diameter is 22 mm, and the washer's inner diameter is 25 mm, which is larger than the hole's permissible outer diameter. Knowing that the axial normal stress in the steel rod is 35 MPa and the average bearing stress between the washer and the timber must not exceed 5 MPa, examine the smallest allowed outer diameter, d, of the washer. %3D %3D +22 mm P Figure 4
w=15
SECTION B(1) Question 1 The bell crank CBA is connected to a pin support B in double shear with 8-mm diameter pin B and to the 10-mm diameter rod CD. Knowing that the ultimate shearing stress is 110 MPa for the steel used in pin B and the ultimate normal stress is 230 MPa for the steel used in rod CD. Determine the maximum vertical force P that can be applied if an overall factor of safety of 1.5 is desired. 45% 300 mm B Figure 1 -450 mm-
Two wooden planks, each 1212 in. thick and 9 in. wide, are joined by the dry mortise joint shown. Knowing that the wood used shears off along its grain when the average shearing stress reaches 1.8 ksi, determine the magnitude P of the axial load that will cause the joint to fail. The magnitude P of the axial load that will cause the joint to fail is kips.
Determine the maximum shearing stress and elongation in a helical steel spring composed of 25 turns of 25-mm-diameter wire on a mean radius of 150 mm when the spring is supporting a load of 2.0 kN. Use Eq. A.M.Wahl Formula and G = 83 GPa.
Link AC is made of a steel with a 65-ksi ultimate normal stress and has a xin. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by-in.-diameter pins, while member BCD is connected to its support at B by a -in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 3.75 is desired, determine the largest load P that can be applied at D. Note that link AC is not reinforced around the pin holes. 16 IN 8 in 16. ---4 in- The largest load P that can be applied at Dis[ lb.
Determine how many 14mm bolts should be used to attach a cap to a cylindrical tank with a diameter of 2.7m and a wall thickness of 15mm that is limited to a normal stress of 115MPA and the allowable stress for the bolt is 190MPA.
For the connection shown, the average shear stress in the 17-mm-diameter bolts must be limited to 260 MPa. Determine the maximum load P that may be applied to the connection. 296 KN 354 KN 444 KN 479 KN 326 kN
Determine the length of the shortest 2-mm diameter bronze wire, which can be twisted through two complete turns without exceeding a stress of 70 MPa. Use G = 35 GPa.