If an electric motor M supplies a cable force of F=(At2+B) N, where t is in seconds and the crate has a mass of M kg and rests on a surface for which the coefficients of static and kinetic friction are u, and H, respectively, find the power output developed by the motor when t = T s. M Magnitude Your Student ID's last digit + 3 Your Student ID's last digit + 35 Parameter Unit A В M Your Student ID's last three digit + 15 kg (Your Student ID's last digit) /10+ 0.1 (Your Student ID's last digit) /10+ 0.15 Your Student ID's last digit + 2 T sec

If an electric motor M supplies a cable force of F=(At2+B) N, where t is in seconds and the crate has a mass of M kg and rests on a surface for which the coefficients of static and kinetic friction are u, and H, respectively, find the power output developed by the motor when t = T s. M Magnitude Your Student ID's last digit + 3 Your Student ID's last digit + 35 Parameter Unit A В M Your Student ID's last three digit + 15 kg (Your Student ID's last digit) /10+ 0.1 (Your Student ID's last digit) /10+ 0.15 Your Student ID's last digit + 2 T sec

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

F = 2U Σ Problem 3 A pilot-scale disc stack centrifuge is tested for recovery of bacteria. The centrifuge contains 25 discs with inner and outer diameters of 2 cm and 10 cm, respectively. The half-cone angle is 35. When operated at a speed of 3000 rpm with a feed rate of 3.5 litres per min, 70% of the cells are recovered. If a bigger centrifuge is to be used for industrial treatment of 80 litres per min, what operating speed is required to achieve the same sedimentation performance if the larger centrifuge contains 55 discs with outer diameter 15 cm, inner diameter 4.7 cm, and half-cone angle 45. HONORE 2Πω2(Ν – 1) 3gtano Q₁ Q₂ 2-2 >₁ 1₂ ||| (r³-ri)
In an experiment designed to determine the value of a parameter n, the actual value that is determined during the experiment is ln n which is determined to be ln n = –1.17828±0.07023. What is the value of n? Make sure that you quote the answer to the correct number of significant figures.
Fundamental Problem The coefficient of kinetic friction between the 40-kg block and the inclined plane is μ = 0.2. (Figure 1) Figure 99°F Sunny 30° 1 of 1 P
A steel rod with a diameter of 25 mm and 831 mm long is heated to 203 °C from an initial temperature of 25 °C. Steel has a modulus of elasticity and coefficient of thermal expansion of 200 GPa and 11.7 x 10-6 /°C respectively. Determine the change in length in millimeters.
has this answered question 3? Express in a manner similar to just what they did in part (2) with their responses. R sin (100πt+α) is the equivalent form of this expression.
(i) Give the correct number of significant figures for: 4500 0.0032 0.04050 (ii) Write in scientific notation and engineering notation: 0.000467 32000000
In a tensile test for an aluminum alloy, the sample used is 2 inches long and 0.5 inches in diameter. The proportional portion of the tension stress-strain diagram for an aluminum alloy is shown below. _x106 lb/in² Pay attention to units and calculate your answer to 1 decimal place for the unit specified above. σ (ksi) 70 t 0.00614 Determine the modulus of elasticity for this material: € (in./in.)
A body is subjected to multiple applied forces and moments. The force present on a 10m area with a planar normal in the k direction (x-direction) can be descríbed by 4i + 3j+ 2k (Newtons). Which of the following describes the mean stress on the 10 m2 area? 5 MPa tangential plus 2 MPa normal 5 MPa tangential 2 MPa normal 5 MPa normal
Please answer within one hr i will give good rating.
In the manufacture of steel balls of the type used for ball bearings, it is important that their material properties be sufficiently uniform. One way to detect gross differences in their material properties is to observe how a ball rebounds when dropped on a hard strike plate. Assuming that each ball has a radius R = 0.3 in., design a sorting device to select the balls with 0.900 < COR < 0.925. The device consists of an incline defined by the angle ở and length L. The strike plate is placed at the bottom of a well with depth h and width w. Finally, at a distance & from the end of the incline, there is a trap with a diameter d. By releasing a ball from rest at the top of the incline and assuming that the ball slides with negligible friction, the ball will reach the bottom of the incline with a speed to. rebound off the strike plate, and then fall directly into the trap (you may want to add a design element that prevents balls from simply rolling into the trap). In your design, choose…
A spherical pressure vessel has an inside diameter of 4 m and a wall thickness of 15 mm. The vessel will be constructed from structural steel [E = 200 GPa; v = 0.29] that has a yield strength of 266 MPa. If the internal pressure in the vessel is 1430 kPa, determine the factor of safety with respect to the yield strength. O 3.55 O 1.76 O 3.28 O 2.54 O 2.79 Attempts: 0 of 1 used Submit Answer Save for Later