Could you please provide correct answer as fast as. Question 4 What are the reaction forces at point A?A1.5 mB20 kN1.5 mсDF-1.5 m +1.5 m10 kN2 mA)Ax= 0 NAy= 17.5 NC)Ax= 17.5 NAy= 0 NE)Ax= 10 NAy= 47.5 NB)Ax= 20 NAy= 32.5 ND)Ax= 0 NAy= 25 NAx= 45 NAy= 0 N

Question 4 What are the reaction forces at point A? A 1.5 m B 20 KN -1.5 m F -1.5 m -1.5 m 10 kN 2 m E A) Ax= 0 N Ay= 17.5 N C) Ax= 17.5 N Ay= 0 N E) Ax= 10 N Ay= 47.5 N B) Ax= 20 N Ay= 32.5 N D) Ax= 0 N Ay= 25 N Ax= 45 N Ay= 0 N

Question 4 What are the reaction forces at point A? A 1.5 m B 20 KN -1.5 m F -1.5 m -1.5 m 10 kN 2 m E A) Ax= 0 N Ay= 17.5 N C) Ax= 17.5 N Ay= 0 N E) Ax= 10 N Ay= 47.5 N B) Ax= 20 N Ay= 32.5 N D) Ax= 0 N Ay= 25 N Ax= 45 N Ay= 0 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You are given a metal rod, cut to a length of 12 in plus/minus .25in. Then you need to cut off 2 in with an accuracy of plus/minus .25 tolerance. You end up with a 10 in rod but what is the tolerance? (hint: rely on the basic principle of tolerance
kindly answer it
*NOTE ON INSTRTUCTUONS AND HINTS
please provide the following: speed rate, deep of cut and measurements of a meat mallet.
for 2 can you please do a sketech veriation of it?
I need these three parts answered (Multiple Choice). If you can not answer all three parts please leave it for another tutor to answer. Thank you. For the two holes identified as datum D, what is the total size tolerance specified for those holes? (Multiple Choice)a. .002'b. .003'c. .004'd. .006' The two holes identified as datum D have a counterbore on one end. What size toleranceis specified for the counterbore diameter? (Multiple Choice)a. .010″ (±.005″; see title block)b. .020″ (±.010″; see title block)c. .030″ (±.015″; see title block) What letter represents the revision status of this print? (Multiple Choice)ABCD
A hole is to be drilled as shown by the circle. Using the part geometry shown below, indicate on the part sketch where locator(s) should be positioned according to the 3-2-1 principle. Use dashed lines to indicate locators on hidden surfaces. Also indicate where clamping force(s) should be applied using arrows. Use the minimum number of clamping forces.
Show all work and steps please
Q1. The part shown below will be turned in two machining steps. In the first step a length of (50 + 50) = 100 mm will be reduced from Ø100 mm to Ø80 mm and in the second step a length of 50 mm will be reduced from Ø80 mm to Ø60 mm. Calculate the required total machining time T with the following cutting conditions: Cutting speed V=80 m/min, Feed is f=0.8 mm/rev, Depth of cut 3 mm per pass. Ø100 Ø80 Ø60 50 50
i need clear ans and solve very very fast in 20 min and thank you | DYBALA A part under forming force showed that 15% decrease in thickness and 10% increase in width, find the change in length (sign and value) if initial length is 200 mm?
Must solve all the questions. Otherwise dont attempt it. If attempted partially, i will surely dislike. So solve all questions.
I need the answer as soon as possible