Ideal Otto cycle with air as the working fluid has a compression ratio of 9.5. The temperature, volume and pressure in the first process are 308K, 100kPa and 0.0006m³. The temperature after expansion is 800K. The air standard assumptions are applicable, both Kinetic and Potential energy are negligible. The mass/mass flow rate is computable. Use the standard constants for air (Cp, Cy, R, and k). Determine the highest pressure and temperature in the cycle, the amount of heat transferred, the thermal efficiency, and the mean effective pressure are to be determined.

Ideal Otto cycle with air as the working fluid has a compression ratio of 9.5. The temperature, volume and pressure in the first process are 308K, 100kPa and 0.0006m³. The temperature after expansion is 800K. The air standard assumptions are applicable, both Kinetic and Potential energy are negligible. The mass/mass flow rate is computable. Use the standard constants for air (Cp, Cy, R, and k). Determine the highest pressure and temperature in the cycle, the amount of heat transferred, the thermal efficiency, and the mean effective pressure are to be determined.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A simple Brayton Cycle uses helium as the working fluid, it has a maximum temperature of 1100 deg.K, and a pressure ratio of 3.3. At the start of the compression, the helium pressure and temperature are 90 kPa and 290 deg.K. Based upon cold-air standard analysis consumptions, determine the following: (a) T2 and T4 in deg.K (b) Heat added in kJ/kg (c) Turbine and Compressor Work in kJ/kg (d) Work net in kJ/kg (e) Cycle efficiency in % (f) Mean Effective Pressure in kPa
THERMODYNAMICS Consider an air-standard Otto cycle with a heat addition of 800 Btu/bm of air, a compression ratio of 7, and a pressure and temperature at the start of the compression process of 13 lbf/in2, 50 F to simulate an actual spark-ignition engine. Determine the maximum pressure and temperature of the cycle, the thermal efficiency of the cycle, and the mean effective pressure assuming the variation of specific heat with the value from table A-19E Show Complete solution on a paper.
4
IMPORTANT: For problem solving items, start your solution by presenting the cycle in P-v and T-s diagrams. Label all points and mark the process where the heat is added and rejected. Also mark the area showing the net work of the cycle. The parameters of the initial state of one kilogram of air in the cycle of an internal combustion engine are o.095 MPa and 65 deg.C. The compression ratio is 12. Compare the values of the thermal efficiency for isobaric and isometric heat supply in the amounts of 820 kJ.
An air-standard dual cycle has a compression ratio of 9.1 and displacement of Va= 2.2L.At the beginning of compression, p1= 95 kPa, and T = 290 K. The heat addition is 5 kJ, with one quarter added at constant volume and the rest added at constant pressure. Determine: a) each of the unknown temperatures at the various states, in K. b) the net work of the cycle, in kJ. c) the power developed at 3000 cycles per minute, in kW. d) the thermal efficiency. e) the mean effective pressure, in kPa. Step 1 Your Answer Correct Answer (Used) Determine each of the unknown temperatures at the various states, in K. 684.1 K T3 = K 1217 T4 = 2311 K 1440 K Step 2 X Your answer is incorrect. Determine the net work of the cycle, in kJ. Weycle = I 3.470026652 kJ Hint Save for Later Attempts: 1 of 3 used Submit Answer Step 3 The parts of this question must be completed in order. This part will be available when you complete the part above.
Q2/ Calculate the thermal efficiency of the heat engine working on the diesel cycle takes in air at 1 bar, 20 °C, and a compression ratio 12 and the highest temperature during the cycle was 1100 °C. Take c, 1.005 kJ/kg-K, c,= 0.718 kJ/kg-K for air.
There are supplied 400 kJ per cycle to an ideal diesel engine operating on 0.5 kg of air. At the beginning of compression, pressure is 100 kPa and temperature is 50 degrees Celsius. At the end of compression, pressure is 4000 kPa. Determine the ff: Compression ratio t2, t3, V3, P4, t4 in degree Celsius, m³ and kPa Heat rejected in kJ Network in kJ Thermal efficiency, % MEP in kPa
3 The total volume displaced in the cylinder for a Carnot Cycle is easily determined with Isothermal expansion ratio True False
THERMODYNAMICS