24 A fluid at °C flows (by forced mode) over the upper surface of a flat plate whose temperature is at 75 °C with a velocity of 1.25 m/s (see figure below). Determine the rate of heat transfer per unit width of the entire plate if the fluid is: a) Air b) Water [Make suitable assumptions if needed] T = 25°C V' = 1.25 m/s Fluid As T = 75°C L = 4 m Figure 3: Schematic for Q-3

24 A fluid at °C flows (by forced mode) over the upper surface of a flat plate whose temperature is at 75 °C with a velocity of 1.25 m/s (see figure below). Determine the rate of heat transfer per unit width of the entire plate if the fluid is: a) Air b) Water [Make suitable assumptions if needed] T = 25°C V' = 1.25 m/s Fluid As T = 75°C L = 4 m Figure 3: Schematic for Q-3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air at a temperature of 27°C (P = 1 atm) and a velocity of 12.7 m/sec flows over the top of a flat mold in order to cool it down (assume this is a flat plate). The mold has dimensions of 1.5 m wide by 0.45 m long (the 0.45 meters dimension is in the direction of the air flow); and is at a temperature of 127°C. a) Find the heat transfer rate from the mold to the air (q). b) Calculate the drag force on the mold due to the air flow.
Engine oil at 40 C [density 876 kg/m^3, viscosity 0.2177 kg/m.s] flows in a 22-cm-diameter pipe at a velocity of 1.1 m/s. The pressure drop (in Pa) of oil for a pipe length of 24 m is ?
Fluid midterm project
16) Fluids
Solve it..
the tube length is 1m.
- Energy equation For steady incompressible flow for one Inlet and one outlet system Power form: W A In terms of Heads: P A P.X 2g sh mgh, POR.. Reynolds Number Re= Power = mass flux g hight: = mgh Wigh P Inertial forces V.,D Viscous forces P D. - Formula sheet 44, Cross sectional are P Print 2100 Res 4000 +α +²₂++h₂ VDpVD Flow in circular pipes Re 2300 laminar flow transitional flow Re 4000 turbulent flow 2x " +1+E₁ Determine: a. The length of segment B (La). b. The total pressure drop (pi-P2). Ch Welke PD Levve Aut L = 250 m O Correction Factor: o Laminar pipe flow : a = 2 o Turbulent flow in a pipe: a = 1 150 m с Beter Au Question 1 For the horizontal series-parallel system of the figure below, all pipes are 7 cm diameter asphalted cast iron (r= 0.12 mm) filled with water at 20°C (- 998 kg/m', -0.001 kg/m.s). The total flow rate is Q-0.0269 m/s, the lengths of segments A and Care LA-250 m and Le - 150 m, and velocity in segment A is l'A- 2.04 m/s. Neglect all minor losses. A (hem 2…
Steam flows steadily through an adiabatic turbine. (CC)) BY-NO-SA Niel Crews, 2013 The inlet conditions of the steam are: pressure = 9 MPa temperature = 450 °C velocity = 80 m/s The exit conditions are: pressure = 10 kPa quality= 0.91 velocity = 50 m/s a) What is the temperature of the fluid at the turbine exit? b) What is the power output of the turbine, per unit mass of the working fluid? kJ kg
Milk at 303K flows at a velocity of 29.5 cm/s through pipe with internal diameter of 5.35cm. The density and viscosity of milk are 1010 kg m -3 and 1.8 x 10 -3 Pa-s, respectively.a) Show that the flow is turbulent.b) What is the change that you need to do to obtain laminar flow?
5
The initially closed valve in Figure III..6.1(b) suddenly opens. Find the flow velocity 5 seconds after the valve is opened. Data: L= 1000 ft, h, = 50 ft, V, = 10 ft/s. [Ans.: A = 3.1 s. and V= 6.7 ft/s]. 1 DA h L d, a (b)
Engine oil at 40 C [density 876 kg/m^3, viscosity 0.2177 kg/m.s] flows in a 21-cm-diameter pipe at a velocity of 1.1 m/s. The pressure drop (in Pa) of oil for a pipe length of 24 m is ?"