Water flow through a pipe with diameter dwater = 0.05 m with a velocity of Vwater = 2 m/s, while oil flows through a parallel pipe with a velocity Voil = 8 m/s. Determine the diameter of he oil pipe (doil = ?) so that both fluids have the same dynamic characteristics. The temperature of the water and oil is 20°C. Properties: For the fluids at T = 20°C, Poil = 880 kg/m³, Pwater = 998.3 kg/m³, -oil = 30.2x10-³ Ns/m² and water = 1.00×10³ Ns/m².

Water flow through a pipe with diameter dwater = 0.05 m with a velocity of Vwater = 2 m/s, while oil flows through a parallel pipe with a velocity Voil = 8 m/s. Determine the diameter of he oil pipe (doil = ?) so that both fluids have the same dynamic characteristics. The temperature of the water and oil is 20°C. Properties: For the fluids at T = 20°C, Poil = 880 kg/m³, Pwater = 998.3 kg/m³, -oil = 30.2x10-³ Ns/m² and water = 1.00×10³ Ns/m².

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The viscosity of motor oil is 4.79× 10-³ N. s/m², motor oil is used as a lubricant between two machine parts. The variation in velocity of the oil is 1.6 m/s and a maximum shear stress is 62.8 N/m². What is the required spacing between machine parts in millimeter?
1. A fluid is bounded by two parallel plates of infinite width and length as shown in FIGURE Q1. The upper plate moves at 7 m/s, and the lower plate is fixed. The fluid's dynamic viscosity is 1.85X105 N.s/m?. Assume Couette flow with pressure gradient, = 0.1 N/m³. a. Propose the discretization method to solve Couette flow equation with pressure gradient below. Let the number of nodes, n = 9, the distance between the nodes is 0.05 m. Obtain the velocity of all the internal nodes using the matrix inversion method and the iterative method. Compare the results and the effectiveness of both methods (in terms of calculation effort and ease of setting up the problem). + b. Flow shear stress is governed by the following equation ôu Propose the discretization method to solve the above equation and calculate the shear stress at node 1. Describe the condition in tems of the pressure gradient when the shear stress at the bottom plate is zero. Moving plate at Um/s N= N-1 `Fixed plate FIGURE Q1
The velocity distribution in a 25 m long and 40-cm diameter pipe is v(r) = 2*(1-25r²) where the velocity units are m/s and radius is in m. Determine the following: (a) What is the drag force (i.e shear force) on the wall for water with an absolute (i.e., dynamic viscosity) of 0.0010 kg/m-s? (b) What is the shear stress at a distance of 5 cm from the centerline of the pipe? R-0 R r=0
Determine the kinematic viscosity (Stokes) of oil having the relative density as 0.91. The shear stress at a point in oil is 1.51 N/m² and the velocity gradient at that point is 0.31 per second. Solution: (i) Viscosity (in Ns/m²) = (ii) Dynamic Viscosity (in poise) = (iii) Mass density of oil (in kg/m³) = iv) Kinematic viscosity (in stokes) =
Water flows at 5m/s is passed through a tube of 2.5 cm diameter, it is found to be heated from 20 °C to 60 °C. The heating is achieved by condensing steam on the surface of the tube and subsequently the surface temperature of the tube is maintained at 90degC. Water properties are as follows: density=995kg/m3, kinematic viscosity=.657x10-6 m2/s, Pr=4.43, k=.628W/mK, cp=4178J/kgK. a) Determine the Reynolds number b) What is the thermal coefficient on question number c) what is the heat absorbed by the water?
Q1) A shaft of diameter (d glycerin-filled sleeve as shown in Figure. The glycerin to be used has a dynamic viscosity of 1.5 Pa.s, and the cable is pulled by 140-N tensile force. If the cable is to be pulled at a velocity of 3.68 m/s and the velocity profile equation though glycerin is (u = 2.4y + 80y2), what is the length of the sleeve that can be used to provide this velocity? Assume that the cable can be kept at the center of the sleeve. = 41-mm) is to be pulled through a (44.1)-cm-diameter Sleeve Shaft P
The velocity distribution in a fully developed laminar pipe flow is given by where UCL is the velocity at the centerline, and R is the pipe radius. The fluid density is ρ, and its viscosity is µ. (a) Find the average velocity . (b) Write down the Reynolds number Re based on average velocity and pipe diameter. At what approximate value of this Reynolds number would you expect the flow to become turbulent? Why is this value only approximate? (c) Assume that the stress/strain rate relationship for the fluid is Newtonian. Find the wall shear stress τw in terms of µ, R and UCL. Express the local skin friction coeffient Cf in terms of the Reynolds number Re.
The velocity distribution of air between two parallel plates is linear. The top plate is moving with a velocity of 5.8 m/s and the distance between two plates is 0.1 cm. Find the shear stress at the lower wall if the dynamic viscosity of air is 2X10-5 N.s/m2. (your answer should be accurate to 5 decimal places)
Water at temperature of 20 °C is flowing inside a straight, smooth pipe with flow rate of 0.05 m3/h . With which pipe diameter will the flow transition from laminar to turbulent? Kinematic viscosity of water at 20 °C is 1.005·10-6 m2/s. Round off the answer to one decimal digit in cm, but enter the answer without the unit.