Consider one-dimensional isentropic flow of air through a converging duct. The air, with temperature of 47 °C and pressure of 91.325kPa, exits the duct at a velocity of 2000 km/hr. The inlet temperature is 60 °C . For air: k-1.4, c=1005 J/kg.K_and R=287 J/(kg.K). Compute a) the stagnation properties, b) the pressure at inlet, c) the velocity at inlet.

Consider one-dimensional isentropic flow of air through a converging duct. The air, with temperature of 47 °C and pressure of 91.325kPa, exits the duct at a velocity of 2000 km/hr. The inlet temperature is 60 °C . For air: k-1.4, c=1005 J/kg.K_and R=287 J/(kg.K). Compute a) the stagnation properties, b) the pressure at inlet, c) the velocity at inlet.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please show your complete solution. Thank you! Air flows in a steady flow manner through a converging tube. At the inlet the pressure is 690kPaabs and the density is 0.838 kg/cu.m. If air enters with a volume flow of 125 cu.m per min at the rate of 94 m/min and the exit section has a diameter of 350mm, determine a.) the mass flow rate, kg/min b.) the diameter of the entrance section and c.) the exit velocity. Assume that the density is constant.
35. Water enters a heated tube of 2 mm diameter at 30 C and leaves the tube at 60 C. Find the water mass flow for the average Reynolds number of 1000. [Ans.: 0.00564 kg/s].
Where necessary, assume air as an ideal gas and consider R = 287J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). a) A nozzle is a device that is used to increase the velocity of a fluidby varying the cross-sectional area. At the last section of a jetengine, air with a mass flow rate of 50 kg/s ata pressure of 500 kPa and a temperature of 600 K enters a nozzlewith an inlet cross-sectional area of 5m2. The exit area of thenozzle is 20% of its inlet area. The air leaves the nozzle at avelocity of 300 m/s. The nozzle is not well-insulated and duringthis process, 5 kJ/kg heat is lost. (i) In analysing this nozzle using the 1st law of thermodynamics,the change in which type of energy is negligible? (ii) Determine the density and velocity of the air entering thenozzle.(iii) Calculate the density of the air as it leaves the nozzle.(iv) Determine the temperature of the air as it leaves the nozzle.(v) Calculate the pressure of the air as it leaves the nozzle.
If air flows in a 20 mm diameter constant area duct at a velocity of 125 m/s with a static temperature of 300 K and a static pressure of 300 kPa, find the rate of heat input required to choke the flow. [Ans. 50.25 kJ/kg]
Thermodynamicss
only 2.6 please 2.5 is included for refrence
B) The air flow to a four cylinder four-stroke engine is 2.15 m³/min. During a test on the engine the following data were recorded: Bore 10.5cm; stroke 12.5cm; engine speed 1200 rpm, torque 150 N.m, fuel consumption 5.5 kg/hr, calorific value of fuel, 43124 kJ/kg, ambient temperature 1-The brake thermal efficiency. and pressure are 20°C and 1.03 barş. Calculate: 2-The brakes mean effective pressure. 3-The volumetric efficiency.
i) Construct the flow chart (diagram) and compute the total heat required to convert 800 g of ice at-50°C to steam at 115 °C. (Cice 2090 J/kg. C, Cwater 4186 J/kg. C, Csteam 2010 J/kg. C, Lf = 3.33 x 10 J/kg, Lv 2.26 x 10 J/kg.)
Q.1. A large tank contains air, gasoline (pc= 680 kg/m³), light oil (p= 800 kg/m³) and water. The pressure p of the air is 150 kPa gauge. If we neglect friction, what is the mass flow rate of oil from a 20- mm-diameter jet? 1₁-2m Air Gasoline 8G Water- 90 Oil.. d. 20 mm #i 2-3m
Where necessary, assume air as an ideal gas and consider R = 287J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). A nozzle is a device that is used to increase the velocity of a fluidby varying the cross-sectional area. At the last section of a jetengine (Fig Q1.a, section 5), air with a mass flow rate of 50 kg/s ata pressure of 500 kPa and a temperature of 600 K enters a nozzlewith an inlet cross-sectional area of 5 m2. The exit area of thenozzle is 20% of its inlet area. The air leaves the nozzle at avelocity of 300 m/s. The nozzle is not well-insulated and duringthis process, 5 kJ/kg heat is lost. (iv) Determine the temperature of the air as it leaves the nozzle.(v) Calculate the pressure of the air as it leaves the nozzle.
I need a simple step by step answer please :)
P (6-5) Two centrifugal pumps are connected in parallel in a given pumping system. Plot total head Ah against capacity Q pump and system curves for both pumps running on the basis of the following data: Operating data for pump 1 Operating data for pump 2 Ahm, 40.0 35.0 30.0 25.0 Ah m. 0.0 35 30 25 Qim³/h. 169 209 239 265 Q₂m/h 0 136 203 267 data for system Ah m, 20.0 25.0 30.0 35.0 Q.m³/h, 0 244 372 470