Using the diagram, determine the minimum diameter for DIA B, in inches. DIA A 0 000 O 00016 BASIC DIMENSIONS DIA A1428 0 DIA B1420 DIA E 00016 0000 0

Q: Enumerate the remaining measurement quantity and Unit

A: Time-si unit second, length-si unit meter, mass-si unit kilogram, electric current-si unit…

Q: Which percentile is typically for designing lower-limit dimensions? - 95th 5th 50th 99th

A:

Q: Provide the sectional front view, looking at the direction X, draw the top view, and left-side view…

A: Find Sectional front view, top view side view, front view, and right side view.

Q: Calculate the Minimum Y distance on the drawing below: 1.000 C 2.000 Ø.995-1.000 I 6.00 0.008 MABC X…

A: given; net distance(Snet)=6tolerance in first circle(T1)=0.008net tolerance in x from both side…

Q: Calculate the Maximum Y distance on the drawing below: 1.000 O .510 O .500 O 2.009 C .460 2.000…

A: Maximum  Y distance is possible when the right side hole is having minimum diameter. The distance…

Q: Metric micrometer. What is the value below? Please show your steps.

A: A micrometre is a device that combines a calibrated screw with other metrological instruments such…

Q: Find the volume described by 0srs 5,0seS T/3, Os O S 2M O a. 125T/3 O b. 251T/3 Oc. 225T/3 Od.…

A: Answer: The volume is 125π/3 . Option (a) is correct.

Q: Draw, using 1 st angle projection Orthographic view of the following figure  with  suitable scale,…

A: (a) the given front elevation;

Q: Draw the isometric and orthographic sketch of the given figure (in catia V5 ;no hand drawing );

A: isometric view

Q: T= second last digit of your matric number. Example: if your 5 and 10+T - 10+4 - 14 (Answer in 2…

A: Given data S=2 T=0 Area of section ABCD= width× hight  = 10×52 = 520

Q: Draw a complete shearing force and a bending moment diagram. Show detailed calculations Use the last…

A: F=54 KNTo determine:Shear force diagramBending moment diagram

Q: Build the following part and report the volume in units cubed. A = 48 B = 51

A:

Q: Draw the orthographic views of the following isometric figure. (Units in mm)

A: According to the details provided in the question, we need to draw three views.

Q: PROBLEM. A mechanism carries a constant load P applied to the seat as given. As CDFE and EFGH is a…

A: Force in pin H and member FG

Q: gedem +x) 1+2) Circle the letter corresponding to the view on the right that shows the result of…

A: First, rotates the object along the y-axis in an anticlockwise direction then again rotates along…

Q: ect with dimension. mode 50 R20 Ø20 25 15 Ø32 Ø60 80 45 50 60

A: According to the details provided in the question, we need to DRAW the half sectional view of the…

Q: Read and record the dimensions indicated by the letters A to H in Figures C-52a to C-52dⒸ. Figure…

A: From the given figure, it is clear that there are 8 divisions between two numbers therefore, value…

Q: s a caliper use to measure inside diameters widths of slots and the like [a)micrometer (b)outside…

A: To determine the correct option.

Q: Identify the drilling operation in which the flat bottom drill bit is used to enlarge the existing…

A: Given Data:

Q: 1. For the following part sizes and geometric tolerances, determine the appropriate geometric…

A: (A) Pin, φ2.062-0.005+0.000  tolerance =upper limit - lower limit tolerance = 0.000-(-0.005)…

Q: Draw the orthographic views of the following isometric figure. (Units in mm)

A:

Q: Convert the bracket into an isometric drawing mark the corner marked A as the lowest point of the…

A: Approach to solving the question: To solve the question, identify corner A as the lowest point and…

Q: Circle the letter corresponding to the correctly aligned set of orthographic views. 1. 2. A 6:6 A E…

A: according to the drawing data we need to find, the right option. that represent the three…

Q: 1ST Dimensions and projections

A: 1 st angle projection

Q: Draw the hologram

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: Draw the isometric projection of the object showing the top, front and right side.

A:

Q: SolidWorks to create the parts.

A: I am using Solidworks to draw a 3-d object of the given problem.

Q: Read the metric caliper in millimeters. Take note that the numbers marked on the main scale are in…

A: The given scale is simple vernier caliper reading. Whose least count is given LC= 0.05 mm  And the…

Q: Write all the commands steps of the AutoCAD software to reach the drawing of the figure below all…

A:

Q: Draw Front View and Top View of the following component

A: Solution:

Q: cm ỏ i 2 3 4 5 6 7 8 9 10 Main Scale Vernier Scale 1. The diameter of a certain circular shaft…

A: Smallest division of main scale =0.1 cm  Number of division in vernier scale =10  Least count =…

Q: Ф 20 30 75

A: Representation of three-dimensional shapes into two-dimensional is known as isometric projection. In…

Q: 100 82 20 32 96 Top view Isometrie view

A: Top view Top view of object is obtained when we see object from top.   Front view Front view of…

Q: Show the tolerance zone created by each of the given tolerance specifications. Superimpose the…

A: We have to show the tolerance zone created by each of the given tolerance specification. And,…

Q: R=200 30 240

A: Find the value of P and thetha.

Q: Draw the orthographic views of the following isometric figure. (units in mm

A:

Q: Draw the isometric views of the following shapes in 1st angle projection

A: Solution: Isometric view means making 3 dimensional figure . The isometric view of given figure is…

Q: Using the diagram, determine the minimum clearance, in inches. DIA A 0.000 0 -0001 6" BASIC…

A:

Q: How many significant digits of decimal degrees are required to match the accuracy of 12h 41m…

A: INTRODUCTION: In this issue, we will convert the hours, minutes, and seconds into degrees, minutes,…

Q: Values for the figure are given in the following table. Note the figure may not be to scale.…

A: Hi, As per the guidelines, we can only provide the type and detailed solution so here we have…

Q: 4. Explain the meaning of the geometric tolerance symbol and complete it with a picture of the…

A: