How many significant digits of decimal degrees are required to match the accuracy of 12h 41m 37.4567s? Convert your answer for units of degrees, arc-minutes and arc-seconds.

Q: Problem 8. The piston shown is moving downward in its track at 26 cm/sec, as shown in Figure 8. All…

A: The piston shown is moving downward in its track at 26 cm/sec, as shown in Figure 8. All dimensions…

Q: =) The magnitude and direction of the velocity of point E, Vg.

A:

Q: m A different pendulum has length 32 inches and is released from rest when 0 = 5° (theta = 5…

A: The length is The angle is The initial velocity is zero.

Q: Angle The above figure shows a component show a isometric view of a casted part which is made up of…

A: the isometric view

Q: Draft and annotate the 2D sketch of housing using AutoCAD and mention all the dimensions. Colour the…

A:

Q: B t Yo = 11 7 10 720s 3.5km Y = Yo⋅ exp (B⋅t) Show how the above formula is used a fx82ms…

A:

Q: How do we write the position or displacement equations for any angle of  theta shown with blue…

A: Given:To find:Position or displacement equations.

Q: In this calculus proble, a machine design has endpoints of a moveable rod of length 1 meter have…

A:

Q: Suppose that you measure the length of an object by using a mictometer caliper and read the measured…

A:

Q: Metric micrometer. What is the value below? Please show your steps.

A: A micrometre is a device that combines a calibrated screw with other metrological instruments such…

Q: Draw the orthographic views of the following isometric figure

A: Given  3D model isometric view To find Orthographic view

Q: Suppose a dimension is indicated on an engineering drawing (with all units in inches) as 1.658 ±…

A: The lower limit of dimension= 1.658 - 0.008 = 1.650 Option third is correct.    Similarly, we can…

Q: NL/H=493 and T₁ = 8 ms Give your answer to the 2nd nearest decimal place. Juve Ln transitions. What…

A: Given data T1=8ms=0.008 sNL/H=493

Q: gedem +x) 1+2) Circle the letter corresponding to the view on the right that shows the result of…

A: First, rotates the object along the y-axis in an anticlockwise direction then again rotates along…

Q: Identify the drilling operation in which the flat bottom drill bit is used to enlarge the existing…

A: Given Data:

Q: 1-14. The density (mass/volume) of aluminum is 5.26 slug/ft. Determine its density in SI units. Use…

A:

Q: Calculate the 1st moment of area and 2nd moment of area for the shape below. The dimensions are…

A:

Q: draw the orthographic view of the above given sketch note using catia v5 software

A:

Q: Draw the orthographic views of the following isometric figure. (Units in mm)

A:

Q: For the following mechanism, if the length of rod AB, /= 2.3 m, and its angular velocity W = 5.7…

A: “Since you have posted a multiple question, we will provide the solution only to the first question…

Q: Situation 3: The speed of the train during the first minute has been recorded as follows: t (s) v…

A:

Q: SolidWorks to create the parts.

A: I am using Solidworks to draw a 3-d object of the given problem.

Q: cm ỏ i 2 3 4 5 6 7 8 9 10 Main Scale Vernier Scale 1. The diameter of a certain circular shaft…

A: Smallest division of main scale =0.1 cm  Number of division in vernier scale =10  Least count =…

Q: c 2. How much money will be accumulated in 20 years from a deposit of $1500 every 6 months if the…

A: Years=20Deposit= $1500 every 6 monthInterest rate= 2.75% per monthEquations given:

Q: aa porticle Torawelo along a The particte incguase Kegagniuude dnd eauation 8x3. heigut pau n y with…

A:

Q: A chain hangs so that its shape is of the form. Y = 75 Sinhx. Determine, correct to 2 decimal…

A: Solution:To find the value of Y when X = 110 for the given equation Y=75sinhX, we can use the…

Q: Using the diagram, determine the minimum diameter for DIA B, in inches. DIA A 0 000 O 00016 BASIC…

A:

Q: What does the expression VB/A mean? O A. O B. Absolute velocity of point B. OC. Velocity of point B…

A: Relative velocity: The rate of change in relative position of one object with respect to another…

Q: Velocity. Suppose the distance travelled by a tanker ship departing from port is given implicitly by…

A: Given the time and displacement relationship. Required: Velocity of ship

Q: Assuming there is no wheel slippage, what is the wheel rotation speed in revolutions per minute of a…

A: Given data: The time for car is t=5 min=300 sec The covered distance is s=181 m The diameter of the…

Q: How do we write the position or displacement equations for any angle of theta shown with blue color.…

A: Given:

Q: Draw the orthographic views of the following isometric figure. (units in mm

A:

Q: Examples 2 : A tangential force of 300N affected the tangents on the upper surface of a parallel…

A:

Q: The bar linkage shown is set in to monon ty applying a counter clockwise angular velocty of 2.7…

A: Givenangular velocity ωCD=2.7rad/slength=0.3mangular acceleration αCD=7.1rad/s2

Q: 20.00 60.00 40.00 FRONT 00 09 0002

A:

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.