30r 20dls 20 10r 20 20 30 150 100

Q: Volume ama the itCTIlal CHcrgy. 4. A vessel of a volume 0.03m3 contains dry saturated steam at 20…

A:

Q: The velocity of a particle moving along the x axis is defined by V = x3 – 4x² + 6x where V is in m/…

A:

Q: 5 400 200 A 1 120° 4 200 (mm) 350 B 2.

A: The number of I centres are given as : N=n(n-1)2N= Number of I centersn = number of links for…

Q: draw the left side

A:

Q: kinelic enorgy ol tro hoop it gium y: the hoop. Then, Cakulale the 1oling down without slipping an…

A: As per the guidelines we are subjected to solve only one question at a time please repost the same…

Q: Question 2 If the force P in the structure below is equal to 450 N, determine the maximum mass of…

A:

Q: Find the acceleration in terms of F. 回 m₁

A:

Q: 1. All the following statements about beams are true, except? a. There are two equilibrium equations…

A: 1. Beams are generally subjected to transverse loads. Hence, (a) There are two equilibrium equations…

Q: Auditorium Hall is to be maintained at a temperature of 24 C dry bulb temperature and 60 % relative…

A:

Q: Complete the following Table (Show all work.) P T V 200 °C H₂0 R-134a H₂0 R-134a H₂0 R-134a H₂0 800…

A:

Q: Two identical solid balls move in opposite horizontal directions at equal speeds. They collide and…

A:

Q: Ø60 60 ALL DIMENSIONS IN mm R15 18 120 36 14 DRAW THE 3RD ANGLE ORTHOGRAHIC PROJECTION & ISOMETRIC…

A: Isometric drawing is given, Draw the orthographic projections.

Q: 7. A SAE steel column has a circular cross-section of 16 mm in diameter and a length of 320 mm. The…

A:

Q: The 40.64 cm. diameter pulley of a gasoline engine is connected by a belt (which is assumed not to…

A:

Q: For an ideal gas, the value of Joule-Thomson co-efficient is?

A:

Q: (a) Draw neat illustrative sketches to bring about the difference between a helical coil tension…

A: Helical spring -These types of springs are made of wire. These springs are supposed to carry load in…

Q: A circular plate of diameter (1.36 m) is placed some how 1.5 meter above the room floor, if the…

A: Solution:

Q: A beam of rectangular cross section 50mm wide and 80mm deep is loaded as shown in Fig:(3.18).…

A: Consider upward force & CW moment as (+)ve and downward force & CCW moment as (-)ve. Let…

Q: 5/ B 3

A:

Q: The drum and shaft are welded together and have a mass of 90 kg with mass center at G. The shaft is…

A: The moment 180 N is balanced by the moment created by the tension in the rope 180 = T ×(radius of…

Q: Draw the figure with projections

A: Draw the figure with projections

Q: the moment was clockwise so wy didnt you subtract it

A: This question is based on the concept of free body diagram and forces.

Q: L HRP FRP (TOP VIEW) (FRONT VIEW) L (RIGHT SIDE VIEW) L

A:

Q: attached file again please , thank you

A: In fluid mechanics, there is a piezometric level which is the imaginary surface above the actual…

Q: Water (5.0 L/min) is flowing in a tube “D = 3 cm, L= 5 m" and is to be heated from 15°C to 60.3°C by…

A:

Q: Let a=4 ft, b=6 ft, c=4 ft and w-7.5 kips/ft. Construct the shear-force and bending-moment diagrams…

A:

Q: at A has coordinates (0, 0). If a load P acts on the ring at 3 becomes EAB = 0.02 in/in., and the…

A: data providedthe length of  rod AB LAB = 5 in the length of rod Ac ,LAC = 8 in The normal…

Q: Given a 2.9 m and b=1.2 m determin the angle EAD Determine the angle EAD, %media:formula85.mml% O

A: The co-ordinates of the points from the given figure in vector for is as below.

Q: A flanged bolt coupling consist of six 10 mm. diameter steel bolts on a bolt circle 300 mm. in…

A:

Q: Let a = 4S m/ sec2, Vo = 5 m/ sec, find V and S at the end of 4 sec.

A:

Q: 1. In a Rankine cycle, steam enters the turbine at 2.5 MPa and condenser at 50 kPa, what is the…

A: Given Dataat 2.5MPahg=2803.1kJ/kgsg=6.2575kj/kg.Kat…

Q: Water is flowing in a tube "D = 3 cm, L= 5 m" and is to be heated from 15°C to 47°C by applying a…

A:

Q: At a point in a strained material, if two mutually perpendicular tensile stresses of 200 kg/cm² and…

A: A stress element is given as shown-Tensile stresses-Also, To Find-The tangential stress on the 15o…

Q: When an inductor and a resistor are connected in parallel, how many degrees out of phase are the…

A: According to Bartleby guidelines, we can solve only three sub part of a question at a time. you are…

Q: 2. The a-t curve for a particle having rectilinear motion is shown in the figure. At t=e, the…

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.