For your company you need to mass produce 20-cmx10-cm heat sinks to dissipate heat quickly from an equipment. After considering several other parameters, you have short-listed two possible designs: A. 72 straight pin fins made of an alloy (thermal conductivity 240 W/m-°C) that costs $9,000 per m³. Each pin is 4 cm long and 1-cm diameter. E.=3'18; $204 B. 64 straight rectangular fins made of another alloy (thermal conductivity 180 W/m-°C) that costs $12,000 per m³. Each pin is 4 cm long and has 2-cmx1-cm cross-section. E =7:94:$6·14 The convection coefficient of the operating condition is approximated as 15 W/m2.°C. Consider that the manufacturing cost is same for both designs but the material cost differs. Calculate and compare the cost and performance (in terms of heat transfer gains by the heat sinks) of the two heat sinks so that a decision can be made to select a design.

For your company you need to mass produce 20-cmx10-cm heat sinks to dissipate heat quickly from an equipment. After considering several other parameters, you have short-listed two possible designs: A. 72 straight pin fins made of an alloy (thermal conductivity 240 W/m-°C) that costs $9,000 per m³. Each pin is 4 cm long and 1-cm diameter. E.=3'18; $204 B. 64 straight rectangular fins made of another alloy (thermal conductivity 180 W/m-°C) that costs $12,000 per m³. Each pin is 4 cm long and has 2-cmx1-cm cross-section. E =7:94:$6·14 The convection coefficient of the operating condition is approximated as 15 W/m2.°C. Consider that the manufacturing cost is same for both designs but the material cost differs. Calculate and compare the cost and performance (in terms of heat transfer gains by the heat sinks) of the two heat sinks so that a decision can be made to select a design.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

GChoose the right answer 1. The temperature profile for steady hest conduction through a plane wall of constant thermal conductivity is a. logarithmic b. parabolic 2. A brick wall (k-0.75 W/mK ) transmits $02 of heat loss through another wall (k-0.25 W/mK, x-100 mm). If the temperature difference across both walls is the same, the thickness of the brick wall would be a.150 mm c. linear 6T b. 240 mm c. 300 mm d. 375 mm 3. The maximum temperature at the center of the solid sphere of radius R having heat generation q (W/m') is given by g'R +9R b. T, + 4k T+9R 6k d. T+9R 8k a. 2k C. 4. The internal thermal resistance of a solid can be ignored if the Biot number is less than a. 1 b. 0.5 c. 0.1 d. Fourier number 5. The ratio of heat transfer of a fin to the heat transfer without fin is referred to as a. fin resistance b. fin efficieney efin effectiveness d. fin conductance.
A solid rectangular parallelepiped is made of aluminum and is initially at 20 C. The base is a 2 cm by 3 cm rectangle and the height of the parallelepiped is 5 cm. The parallelepiped is now dropped into hot oil at 150 C. Find: a) the temperature of point P and b) the temperature of the center of the parallelepiped after 2 min of exposure to hot oil. Point P is located 1 cm above the center plane and1 cm from each side.
Conduction Heat Transfer X material (a) material (b) . both (a) and (b) have the same thermal conductivity the temperature distribution is independent of thermal conductivity it's not that simple 9. Fin efficiency is defined as: • tanh (mL) (hP/k Ac)1/2 (heat transfer with fin) / (heat transfer without fin) (actual heat transfer through fin) / (heat transfer assuming all fin is at T = Tb) (Tx=L-Tf)/(Tb-Tf) 10. For an infinite fin, the temperature distribution is given by: (T-Tf)/(Tb-Tf)= e-mx. The heat flow through the fin is therefore given by: k (Tb-Tf)/L ● zero, because the fin is infinite ● infinite because the fin is infinite ● (Tb-Tf) (hP/k Ac)1/2 ● (Tb – Tf) (h P / k Ac)1/2 tanh (mL) 11. The Biot number, Bi, is defined as: • Bi=hk/L • Bi=hL/k • Bi= k/LH • Bi=qL/k • Bi=p UL/k 12. For a plate of length L, thickness, t, and width, W, subjected to convection on the two faces of area L x W. What is the correct length scale for use in the Biot number? . L ● W ● t • t/2 • L/2 13. If Bi…
I need right solution with clear calculations. A workplace is occupied by 100 people who are averaging 250 Watts/person. The space is measured as 30 meters x 20 meters x 15 meters (L x W x H). What is the internal heat gain of this space given off by a full staff? If you need to provide the workplace 10 air changes per hour, what type of infiltration inflow rate need to be (cubic meters/hour)?
1. Suppose you have a 4-foot metal rod, made out of steel which has a thermal conductive factor of a = 4 Assume the temperature on the ends of the rod is always 0 degrees. a) Filling in the numerical parameters mentioned above in the problem, write down the general solution to this heat equation, which should include some unknown coefficients (c,'s), in addition to t's and x's.
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
Q1: If a calorimeter is not assumed to be adiabatic, how would one calculate the heat transfer? Guide Questions: What are the parameters to be considered and the equations to be used? What law of thermodynamics does this transfer of heat to the surroundings touch? Is an adiabatic system automatically considered as a closed system? Please help me understand by also attaching a reference/book/journal article. This would help me in my essay. Thank you.
Match the appropriate thermal conductivity walue for the given materials Material Thermal Conductivity (K) 4. Diamond 0.026 W/m K B. Copper 2. 0.607 W/m K c. Water 3. 385 Wm K D. Ar 2300 Wm K O a. A-I, B-IV, C-I, D-I O b. A-II, B-I C-I D-IV Oc A-IV, B-II, C-II, D-I O d. A-I, B-I, C-II D-IV
Find the thermal resistance r (in hr - °F/BTU) and the equivalent R-value (in hr ft?. °F/BTU) of a typical frame 20' x 7.5" wall consisting of a 0.5" plaster board on the inside of the room, nominai 2 x 4 studs, and a 0.5" sheathing on the outside. The spaces between the studs are filled with an R-15 insulating foam. What is the heat loss (in BTU) through this wall in four hours if the inside temperature is 72°F and the outside temperature is 32°F? (Assume that the 15% of the wall's area are studs and the remaining 85% is filled with the insulating foam. Assume that the air is moving outside the wall.) r= 0.0805 x hr: OF/BTU R=0.09 x hr ft2. F/BTU AQ = BTU
Aircraft Fuselage Aircraft Hull Figure 3 a) Consider two large hull as in Figure 3 above made of foam for Amphibian Aircraft has a volume of 80 m3 each, and the total mass of the aircraft when empty is 7000 kg. Determine how much luggage this Amphibian Aircraft can carry without sinking when landing (i) in the lake which have fresh water and (ii) in seawater with a specific gravity of 1.03. b) Please analyse and give the recommendation on the stability of the aircraft when landing in the water if the luggage compartment has been fully filled. The luggage compartment has been located at the centre of the aircraft fuselage. Hìnt: Draw locations of centre of gravity (CG) and centre of buoyancy (CB) to support your answer.
My buddy is starting to get hypothermic (body temperature 306 K) during an epic backcountry ski adventure. Since I'm quite warm (body temperature 310 K), I decide to get in a sleeping bag with him to try and warm him up. What heat transfer mechanism will be most responsible for heating him up? For simplicity, ignore any internal temperature differences across my body (that is, assume my skin temperature is also 310 K). Use numbers to support your answer (for human skin, you can use the following values: surface area A = 1:50 m2, emissivity = 0:970, thickness d = 0:0250 m, thermal conductivty 0:200 JmsK)
1-) Die casting is a metal casting process that is characterized by forcing molten metal under high pressure into a mould cavity. A circular die (k = 150 W/mK, T = 125 °C) is used to drill a hole (D = 0.5 m) along length L = 3 m through a cylindrical metal (D = 2 m) as shown in the figure. A cooling fluid (k = 0.6 W/mK) passes through the hole during the process to keep the inner surface temperature of the hole to 85 °C. In the meantime, the outer surface temperature of the cylinder is held at 30 °C. The hole is drilled eccentrically (not in the origin of the cylinder, 0.1 m perpendicular distance) as shown in the figure. If the heat loss through the cylinder is XY kW during this process, what is the thermal conductivity of the cylindrical metal? (Take the heat loss value XY as a 49 2m 0.1m %3D 3m