I The 45 degree strain rosette is mounted on a steel shaft. The following readings are obtained from each gauge: Ea = 700(10-6), 6, = 400(10-6), €c = -350(10-"). Determine (a) the in-plane principal strains; (b) the maximum in-plane shear strain and associated average normal strain. In each case show the deformed element due to these strains. (c) Determine the absolute 45 maximum shear strain.

I The 45 degree strain rosette is mounted on a steel shaft. The following readings are obtained from each gauge: Ea = 700(10-6), 6, = 400(10-6), €c = -350(10-"). Determine (a) the in-plane principal strains; (b) the maximum in-plane shear strain and associated average normal strain. In each case show the deformed element due to these strains. (c) Determine the absolute 45 maximum shear strain.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
NOTE: PLEASE ANSWER ALL OF THE QUESTIONS AND PROVIDE STEP BY STEP SOLUTION
i need the answer quickly
i need the answer quickly
The lap joint is connected together using a 32 mm diameter bolt. Determine the permanent shear strain in the shear plane of the bolt when the applied force P = 750 kN is removed. Note: The bolt is made from a material having a shear stress-strain diagram as follows T (MPa) A { 600 400 5 50 y (10³ rad)
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L1 = 55 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.8 ksi. Brass segment (2) has an outside diameter of 0.35 in., a wall thickness of 0.07 in., a length of L2 = 38 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.3 ksi. Determine:(a) the allowable torque TB that can be applied to the compound shaft at flange B.(b) the magnitudes of the internal torques in segments (1) and (2).(c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
bb3 please help me this is my last attempt
3. For the stress state below, find all three principal stresses and three maximum shear stresses. Draw a complete Mohr's three-circle diagram. Given the stress state: 0xx (cw). 50 MPa, oz = -20 MPa, txy 30 MPa [Hint: Following the procedure in the in-class example problems done by the instructor.]
The axial load 396 kN applied to the lap joint is distributed equally among the three 20.6-mm-diameter rivets. What is the maximum tensile stress (in MPa) in the plate if w = 135.4mm and t = 27.1mm? Round off the final answer to three decimal places.
Determine the stresses in two segments of the bar shown. Segment A has a diameter of 1 and1/4 inches and segment B has a cross-section 2in by 2in
i need the answer quickly
please answer asap