I need an expert's solution to the following questions in a simple manner, without too much explanation. 1. What are the features of star and delta connected windings? 2. What will happen if transformers are connected in parallel without satisfying the necessary conditions? 3. Out of the conditions for successful parallel operation listed above, state which of the conditions must be strictly satisfied and which of the conditions permit deviation? 4. What do you mean by transformer connection Yd1 and Dy11? 5. Draw the connection diagram for two parallel transformers with (A-A) connected? 6. Why the following connections are not possible for parallel operation? First Transformer Y-Y Y-Y A-A Second Transformer Y-A A-Y Y-A

I need an expert's solution to the following questions in a simple manner, without too much explanation. 1. What are the features of star and delta connected windings? 2. What will happen if transformers are connected in parallel without satisfying the necessary conditions? 3. Out of the conditions for successful parallel operation listed above, state which of the conditions must be strictly satisfied and which of the conditions permit deviation? 4. What do you mean by transformer connection Yd1 and Dy11? 5. Draw the connection diagram for two parallel transformers with (A-A) connected? 6. Why the following connections are not possible for parallel operation? First Transformer Y-Y Y-Y A-A Second Transformer Y-A A-Y Y-A

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.11MCQ: For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the...

See similar textbooks

Similar questions

An ideal transformer has no real or reactive power loss. (a) True (b) False
Rework Problem 3.14 if the transformer is delivering rated load at rated secondary voltage and at (a) unity power factor, (b) 0.8 power factor leading. Compare the results with those of Problem 3.14. -
In per-unit equivalent circuits of practical three-phase transformers, under balanced thr-phase operation, in which of the following connect ions would a phase-shifting transformer come up? (a) Y-Y (b) Y- (c) -
The ideal transformer windings are eliminated from the per-unit equivalent circuit of a transformer. (a) True (b) False
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
For an ideal 2-winding transformer, the ampere-turns of the primary winding, N1I1 is equal to the ampere-turns of the secondary winding, N2I2 (a) True (b) False
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) False
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.