I Design a CS amplifier using E-MOSFET with voltage gain 6 , Ves=6V (gm-4500uS ).Il-(a) State the fundamental operating principle of the field-effect transistor as a switch.(b) Design a MOSFET NOR circuitIII Find the Q point of the given JFET circuit.VDD+6 VIpss 5 mA. Vp-4V820 0RG10 MQRs330 NIV From the circuit of common source JFET amplifier shown in the figure,its has VGS(of = -2.0V,Ipss = 1.4mA. If you need this amplifier to be biasedwith Ip =0.7mA, VDp= 20V, and voltage gain of 20DB,what is the value of RS, and RD?C3VoutAssignment Home Work

“Since you have asked multiple questions, we will solve the first question for you. If you want any…

I Design a CS amplifier using E-MOSFET with voltage gain 6 , VGs=6V (gm-4500uS). Il-(a) State the fundamental operating principle of the field-effect transistor as a switch. (b) Design a MOSFET NOR circuit VDD III Find the Q point of the given JFET circuit. +6 V Inss 5 mA. Vp 4V 820 N RG 10 MQ Rs 330 N IV From the cireuit of common source JFET amplifier shown in the figure, its has VGS(of = -2.0V, Voo Ipss = 1.4mA. If you need this amplifier to be biased with Ip -0.7mA, Vpp=20V, and voltage gain of 20dB, what is the value of RS, and RD? C3 out Assignment Home Work

I Design a CS amplifier using E-MOSFET with voltage gain 6 , VGs=6V (gm-4500uS). Il-(a) State the fundamental operating principle of the field-effect transistor as a switch. (b) Design a MOSFET NOR circuit VDD III Find the Q point of the given JFET circuit. +6 V Inss 5 mA. Vp 4V 820 N RG 10 MQ Rs 330 N IV From the cireuit of common source JFET amplifier shown in the figure, its has VGS(of = -2.0V, Voo Ipss = 1.4mA. If you need this amplifier to be biased with Ip -0.7mA, Vpp=20V, and voltage gain of 20dB, what is the value of RS, and RD? C3 out Assignment Home Work

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the figure, A characteristics curve is shown for the MOSFET. Determine the following outcome and parameters using the values given in the characteristics: i) Find the Ip for the VGs = 4V, where IGs(ON) = 4.5mA ii) Find the transconductence of MOSFET; where, MOSFET having the bias voltage VGs = 4V, and 6V. %3D A (mA) A5 (mA) 10 10 VGs=+8 V 9. 7 .7 VGs =+7 V 6 5 Vas=+6 V 4 VGs =+5 V 2 VGs =+4 V Vas =+3 V 1 3 4. 5 8 Vas 10 15 20 25 Vos Vas = VT=2 V a co
Enclosed please find an amplifier circuit designed with a BJT transistor. VCC = 9Volt for the circuit. All capacity values are selected sufficiently large. BJT Transistor B = 100 Vbe(on) = 0.8V, VA=100V, Vt= 26mV Vce (sat) = 0.15Volt. Calculate “Vceq” and “Icq “ values at the operating point of the circuit. In what area does this BJT transistor work in? Draw the small signal equivalent circuit of the circuit. Calculate the AC small signal current earnings of the circuit (Ai = I out / I input). Note: Is the current passes over Rs source resistance and The IO current passes over RL source resistance. Please Calculate Rin input resistance?
Elecronics Engineering
Pls answer the following. Thank you
1. To use the Bipolar Junction Transistor (BJT) as a small signal amplifier it must be biased in this region: A. South Park region B. Spatial interface region C. Inverse Thevenin region D. Linear or active region
2. The parameters of the transistor as shown in the figure below are ß = 100 and VA = 100V. a. Find the dc voltages at the base and emitter terminals. b. Find Rc such that VCEQ = 3.5V. c. Assuming Cc and CE act as short circuits, determine the small-signal voltage gain Av = Vo/Vs. d. Repeat part (c) if a 5000 source resistor is in series with the vs signal source. V+ = +5 V Rs = 100 £2 www Us Cc RB = 10 ΚΩ I= Iausmi 0.35 mA www RC -000 V=-5 V CE
estion 2: Consider the BJT circuit given here. ( Write the input and output loop equations For the given values of Vcc= 10 V, Vin = 4V and resistor values, calculate all current values (IB, IC and IE) and VCE Assume that the ß for the transistor is 100 and the voltage drop across LED connected between Collector terminal and resistor (Rc) 2.1 V. TH i. ii. 111. VIN Vcc Rg=100 kΩ Re=2 kΩ LED 2.1 V B= 100 Based on the above analysis, correctly identify the current mode of operation Cutoff mode Active linear mode Saturation mode
c) Figure 2.3 shows the circuit diagram of a typical npn BJT common emitter amplifier. The values of RB1-30 kOhm, RB2=10.XY kOhm, Rc-3.XY kOhm, Ic=2.XY mA and Vcc=24 V. If the transistor current gain 3 = 50 determine using the full analysis and assuming VBE = 0.7 V the value of RE, hence identify the location of the Q-point (Ic, VCE, IB and VBE). Now sketch the AC circuit model of this amplifier and determine the value of the ac open circuit voltage gain Av and the ac short circuit current gain Ai. (Assume that Vth = 26 mV). Vin RB1 Cin lin RB2 -10 Rc VB RE + Vcc Vc Cout VE www li Figure 2.3 Vout Ce ¡out x=1 y=7
Design a self-bias network using a JFET transistor with IDSS = 8 mA and VGS(off) =-6V to have a Q-point at IDQ =3,5 mA using a supply of 14 V. Assume that RD=3RS.A simple circuit may do. Thank you!
An NPN bipolar junction transistor having VB > VE and Vc = (VB - 400 mV) is: Select one: O a. Operating in saturation. O b. Operating in deep saturation. O c. Operating in active mode. O d. Operating at the edge of soft saturation. In order to operate in the active mode. annpn transistor must have VBE 0 and Vec Select one: Tue
Which of the following models can be used for BJT AC SImall signal amplifier circuit analysis? i. hybrid model ii. re model iii. transconductance model iv. Eber's Moll model II, ili and iv i,i and iv O ii and iv O i and ii
For the given Common Emitter NPN Amplifier, the transistor made of Germanium diodes, BDC-80, Vcc Rc-3.9 K2, RE-0.68 KQ. a) Name the type of biasing used in the above circuit? 1 = 16 volts, R= 62 KQ, Rz 9.1 K R, Rc Cs b) Find VE? Find VCE? d) Find Vc? e) What is the name of the capacitors C1, C3 and C2?