b) Consider a MOSFET circuit with transistor parameters VTN=0.8V, KN=0.85 mAVand A=0.02V1.i) Determine Rs and Ro such that loo=0.15mA and Voso=5.5vi) Calculate the small signal parametersi) Draw the small signal equivalent circuit and determine the voltage gain.+5VRDCo+VoRL=50KVGsRs-5VFigure Q4bww

We will do DC analysis to find out resistance and small signal parameters .

b) Consider a MOSFET circuit with transistor parameters VT=0.8v, Kv=0.85 mAV and A=0.02V. i) Determine Rs and Ro such that Ioo=0.15mA and Voso=5.5V Calculate the small signal parameters i) Draw the small signal equivalent circuit and determine the voltage gain. +5V RD O +Vo +V. O RL=50K VGs Ro Rs -5V Figure Q4b ww

b) Consider a MOSFET circuit with transistor parameters VT=0.8v, Kv=0.85 mAV and A=0.02V. i) Determine Rs and Ro such that Ioo=0.15mA and Voso=5.5V Calculate the small signal parameters i) Draw the small signal equivalent circuit and determine the voltage gain. +5V RD O +Vo +V. O RL=50K VGs Ro Rs -5V Figure Q4b ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

VDD = 16V, VGG = -3V, RG = 1.2 M-ohm, RD = 2200ohm, IDSS = 10mA, VP=-4.5Va)Determine the drain current ID in mA.b)Determine the gate voltage, VGc)Determine the source terminal voltage, VSd)Determine the gate-to-source voltage, VGSe)Calculate the drain terminal voltage, VDf)Determine the drain-to-source voltage, VDS
Determine vo versus v₁ for the circuit shown in Figure 2. Assume that the MOSFET operates in saturation and is characterized by the parameters K and VT. Vs R₁ www Figure 2 wwww RL R₂ wwwww VO Note: assuming the MOSFET works at normal saturation regime and ips= (VDS -VT)²2 K 2
5. Determine Ic and Vce in the pnp emitter bias circuit. Assume 6pc = 150 VEE +10 V RE 470 N RB 10 kN Rc 330 N -10 V Vcc
Electrical Engineering A uniformly doped silicon pnp bipolar transistor is to be designed with NĘ = 1019 cm³ and Nc = 1016 cm³. The metallurgical base width is 0.75 µm. Determine the minimum base doping so that the punch- through voltage is no less than 25 V.
Problem-5 The LED in Figure below requires 30 mA to emit a sufficient level of light. Therefore, the collector current +Vcc should be approximately 30 mA. For the following circuit values, determine the Re amplitude of the square wave input voltage necessary to make sure that the transistor saturates. Use double the minimum value of base current as a safety ON ON margin to ensure saturation. OFF Vcc = 9 V, VCE(sat) = 0.3 V, Rc = 220 N, RB = 3.3 kÝ Bpc =50, and VleD = 1.6 V. 1
2. Determine the VCB (i.e., voltage difference between collector C and base B) in the transistor circuit shown in the figure below. The transistor is silicon type (i.e., VBE is 0.7V) and has current gain hEE- 150. (Assume the transistor is working on active region) Rc 100 2 RB 10V Vcc 10 k2 VBR = 5V
1. To use the Bipolar Junction Transistor (BJT) as a small signal amplifier it must be biased in this region: A. South Park region B. Spatial interface region C. Inverse Thevenin region D. Linear or active region
2. The parameters of the transistor as shown in the figure below are ß = 100 and VA = 100V. a. Find the dc voltages at the base and emitter terminals. b. Find Rc such that VCEQ = 3.5V. c. Assuming Cc and CE act as short circuits, determine the small-signal voltage gain Av = Vo/Vs. d. Repeat part (c) if a 5000 source resistor is in series with the vs signal source. V+ = +5 V Rs = 100 £2 www Us Cc RB = 10 ΚΩ I= Iausmi 0.35 mA www RC -000 V=-5 V CE
TEST Read the question carefully. Write the letter for each correct answer in the blank space provided. A 1. Maximum power is delivered from a source of power to a load when the a. load current is equal to the power source current b. impedance of the load is equal to the output impedance of the power source c. output impedance of the power source is high compared to the impedance of the load d. output impedance of the power source is low compared to the impedance of the load 2. The emitter follower is a (an) a. impedance matching device b. high gain voltage amplifier c. phase inverter d. combination power and voltage amplifier 3. The emitter follower uses a. no collector resistor b. a forward bias collector-base junction c. negative feedback (degeneration) d. an NPN transistor only 4. The emitter follower has output resistance. a. high, high b. low, low c. low, high d. high, low input resistance and 5. The current gain of an emitter follower is a. less than 1 b. equal to 1 c. greater…
(ii) Calculate the RB, Rc, and the minimum power rating of the transistor (Note: the actual power rating should be greater).