i) Calculate the acceleration of mass A in the system with three 10 kg cylinders as shown in Figure 2. Neglect friction and the mass of the pulleys and cables. ii) Calculate the velocity of mass A after mass A has moved 6m, given A has a mass of 10kg. Assume the system starts from rest 500 N 250 N A 10 kg 10 kg 10 kg

i) Calculate the acceleration of mass A in the system with three 10 kg cylinders as shown in Figure 2. Neglect friction and the mass of the pulleys and cables. ii) Calculate the velocity of mass A after mass A has moved 6m, given A has a mass of 10kg. Assume the system starts from rest 500 N 250 N A 10 kg 10 kg 10 kg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer all becuase they are all connected! UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Answer in 3 decimal places! Strength of Materials The steel wide-flange beam has the dimensions shown. If it is made of an elastic perfectly plastic material having a tensile and compressive yield stress of o,, determine the following: Given: Allowable Stress = 300 MPa a = 20 mm b = 250 mm c = 250 mm This is already answered in bartleby but please recheck. Thanks a. Calculate the moment of inertia I, in x10 mm4 (If your answer is 667,335 x10 mm, then type 667.335) b. Calculate the yield moment of the section in kN.m. c. Calculate the plastic moment of the section in kN.m d.Calculate the shape factor of the section.
Formula Sheet Calculator 0 = 90° -- 0 = 0° A A'
Please give proper rough sketch with dimensions and try to solve within 20 minutes
QUESTION 2 A shaft rotates at 300 rpm. 1). If it carries a spur gear that delivers 5 hp to a mating gear and the spur gear has the diametrical pitch of 10, pressure angle of 20°, and 80 teeth, determine a). The resultant force exerted on the shaft = Ib 2). If it carries a sprocket that delivers 4 hp to a mating sprocket and the sprocket has the pitch diameter of 6", determine b). The force exerted on the shaft Ib 3). If it carries a "flat-belt pulley" (Note: NOT V-Belt Drive) that delivers 8hp to another flat-belt pulley and the pitch diameter of the pulley is 20", determine C). The force exerted on the shaft: Ib
solve show full solution
Please provide neat solutions thank you
1. If a machinist wanted to drill a % inch hole in a piece of machine steel using a high speed steel drill. At what speed in revolutions per minute should he operate the drill press? 2. Find the revolutions per minute of an 8 mm drill if it is used to cut an aluminum workpiece using a high carbon steel drill. 3. The rpm setting of the drill press is set to 600 rpm. What is the maximum diameter in inches of a high speed drill if it is used to drill a tool steel material? 4. A drill press has the following rpm settings; 350, 600, 1100, & 1600. What rpm setting must be used if a 15 mm high speed steel drill is used to cut brass workpiece? 5. A machine operator drills a hole of a 3/8 inch diameter to a stainless steel using a carbon steel drill. He sets the drill press rpm setting to 900 rpm. Is he operating at correct setting? If not, then what must be the correct rpm setting considering that the machine has the following rpm settings of 300, 600, 900, 1200, and 1800?
The answer is one of the options below please solve carefully and circle the correct option Please write clear .
I need problems 7, 8, and 9 answered pertaining to the print attached below.
Need only correct answer . I will vote.
solve 30-40 mins.hand written asap
Required information Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has a 1.250-inch-thick bar that needs 90° grooves machined into it for precision ground 1.0000-inch diameter cylinders. A sine bar is used by placing different thicknesses under one of the cylinders so that the proper angle is attained. Sally wants the distance between the centers of the cylinders to be D= 5.4 inches. -D -1.0000 Ø How deep should she mill the 90° grooves so that the top of the sine block is 2 inches tall? The depth of the mill should be inches.