How many 10-mm-diameter steel bolts can be used on a 600-mm bolt circle coupling so that the shearing stress does not exceed 100 MPa in the bolts and the torque capacity can be raised to 72 kN·m? Group of answer choices 28 15 31 30

Q: d Given: 9/8 in 2 in Diameter of bolt = 7/8 inch Diameter at the root of the thread (bolt) = 0.731…

A:

Q: A load P is supported by two springs arranged in series. The upper spring has 20 turns of 20-mm…

A:

Q: Select a standard threaded round rod to support a factored tensile load of 35 kips (service tensile…

A: Given: The fractured load, Pf = 35 kips The service load, Ps = 25 kips The yield strength of A36…

Q: 0 W12X31 6-120 1.10m 4.20m 3.2n

A:

Q: A steel tube with a circular cross section has an outside diameter of 310 mm and wall thickness of 2…

A: For the hollow tube the torsional stress is maximum at the outer periphery so it is calculated by…

Q: P P= 1800 KN allowable shear stress in a bolt=210MPa What is the minimum bolt diameter that may be…

A:

Q: A 260 mm bar AB with a rectangular cross section of 17 × 30 mm, consists of two aluminium layers…

A:

Q: The shaft in (Figure 1) is used to transmit 32 hp while turning at 600 rpm. Figure 2 in. 2.5 in. 1…

A:

Q: Two 1/4 in × 8 in A36 steel plates are joined with a lap joint using 3/4 in A325-N bolts. If a…

A: Steel plates of size 14 in × 8 in of A 36 steel Ultimate tensile strength of A 36 steel is…

Q: Bar (1) has a cross-sectional area of 0.75 in.?. If the stress in bar (1) must be limited to 35 ksi,…

A:

Q: The bolted connection carries a load as shown. What is the minimum size of the bolt if the allowable…

A:

Q: Required information A steel tube with a circular cross section has an outside diameter of 310 mm…

A: Steel tube with a circular cross section outside diameter D= 310 mm t= 2mm.  length, L=  2 m torque,…

Q: Problem 3: A Hexagonal bolt connects two members. The joint has a gap 1 = 2 in and the applied load…

A: Given data: The gap (or) length of the bolt, l = 2 in Applied load, P = 2000 lb 5/16 in 18 UNC-2A…

Q: d Given: 9/8 in Diameter of bolt = 7/8 inch V2 in Diameter at the root of the thread (bolt) = 0.731…

A:

Q: Figure 8-19 is a cross-section of ASTM A36. A total of N bolts are to be used to resist a separating…

A: according t o given question

Q: ) The 100-mm long 2014-16 aluminum rodi has a diameter of 15 mm. If an axial tensile load of 10 KN…

A:

Q: 3. Two ½ in. thick A36 steel plates are joined with two % in. thick A36 steel splice plates and…

A: It is asked to find the smallest bolt size to support the load of 55 kips

Q: The axial load 274 kN applied to the lap joint is distributed equally among the three…

A: Given:  P = 274 kN n = 3 d = 26.5 mm  w = 135.4 mm  t = 29.5 mm

Q: A flanged bolt coupling consists of eight – 10mm diameter steel bolts on a bolt circle 500mm in…

A:

Q: 4 F = 386,000 lb 36" LONG Stainless Steel Annealed 3870 rod F = 386,000 lb A = O= Will the rod fall?…

A: According to our guidelines, we are supposed to answer the first three sub parts. Please repost…

Q: A box of negligible size is sliding down along a curved path defined by the parabola y=0.40x2. When…

A: Given:-  Equation of path is given by  Y = 0.40 x2 When box is at A (2, 1.6), the speed is 12 m/s…

Q: 1/2-inch thick steel bar is welded to the vertical support A) Calculate the allowable load if the…

A: Given data as per the question h = 3/16 = 4.7625 mm d =4'' = 101.6 mm L =12''=304.8 mm

Q: The five-bolt connection must support an applied load of P = 3900 lb. If the average shear stress in…

A:

Q: Q1:Prepare a full-section assembly drawing of the four fastener assemblies shown in the Figure.…

A: To find:The clearance and the threaded holes.Consider the top view:

Q: For a bolted assembly with six bolts, the stiffness of each bolt is kb = 1.8 Mlbf/in and the…

A: If you have any doubts,do write in comments.

Q: The figure below shows two plates connected by two rivets. The plates are made from aluminum 6061-T6…

A:

Q: Write the given data. Type of bolt=SAE grade 2F=20000 lbn= 50=0.750proof Calculate the load on each…

A:

Q: 5275 is a commonly used grade of steel For this grade, the ultimate tensile strength fy=? Select…

A: Answer For First:- According to standard for mild steel code S275 Composition: Carbon 0.25%…

Q: Q1: The shaft (AB) is supp rted on the bearings A and B as shown in figure below. The shaft is…

A: Given:Tension in the rope, T=4.5 kN or 4500 NFactor of safety, Fos=2diameter of drum, d=200 mm

Q: ensile force of 37 kN without stretching more than 5 m

A:

Q: Part A Determine the smallest diameter of the rod that will support the load ofP = 3.4 kip without…

A:

Q: Two in. thick A36 steel plates are joined with two % in. thick A36 steel splice plates and twelve…

A: It is asked to find the smallest bolt size to support the load of 55 kips

Q: Required information A rotating shaft of 25-mm diameter is simply supported by bearing reaction…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: P P= 1300 KN allowable shear stress in a bolt=210MPa What is the minimum bolt diameter that may be…

A:

Q: A flange bolt coupling is used to connect two solid shaft 90 mm in diameter. If the shearing stress…

A: Given Data: Diameter of the shaft, ds=90 mm Diameter of the bolts, db=10 mm Shear stress, 55 MPa

Q: Q1. Design and draw a protective type of cast iron flange coupling for a steel shaft transmitting 28…

A:

Q: Table 7-1 11) Determine the available tension capacity (LRFD) of the connection with A36 steel…

A: according to AISC Steel Manual 13th Ed AISC Steel Manual Table  no 1-7 (P 1-42) given,  Angle…

Q: -The connection shown in the figure if the screw is type 98 and the two plates are A'SI 1040 CD…

A:

Q: The machine component has been fabricated using machining and is made of stainless steel (Sy= 276…

A: Given that, Given material is Stainless Steel,Syt=276 MPa,Sut=568 MPa,f=0.9Reliabilty=95…

Q: The bolt AB in (Figure 1) has a diameter of 24 mm and passes through a sleeve that has an inner…

A:

Q: A -0.5 m- 400 KN B -0.5 m- C 0.4 m D E F Figure 2 (not to scale) The assembly shown in Figure 2…

A: Answer: ◆ The normal stress in post AD and CF: 168 MPa. ◆ The normal stress in post BE: 43 MPa.

Q: A flange bolt coupling consist of 8-12.7mmꬾ steel bolts on a circle diameter of 304.80mm & 6-12.7mmꬾ…

A:

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.