13. A cylinder with a bore diameter of 3 in and a rod diameter of 1.38 in is required to extend against a load of 15,000 lbs and to retract against a load of 750 lbs. What pressure is required for each stroke?

13. A cylinder with a bore diameter of 3 in and a rod diameter of 1.38 in is required to extend against a load of 15,000 lbs and to retract against a load of 750 lbs. What pressure is required for each stroke?

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter22: Welding Joint Design And Welding Symbols

Section: Chapter Questions

Problem 4R: Sketch a V-grooved butt joint, and label all of the joint's dimensions.

See similar textbooks

Related questions

Q: A gear reduction system consists of two gears: E and X. Gear E rotates clockwise with a constant…

A: Given data: αE=4.5 rad/s2ωE=7 rad/s Need to determine select the correct statement.

Q: 10-3. The state of strain at a point on a wrench has components €, = 120(10“), Yay = 150(i0*). Use…

A: 10-3 Given, εx=120×10-6εy=-180×10-6γxy=150×10-6 For our ease of calculation, we neglect the 10-6 in…

Q: PROBLEM: Find the transfer function, G(s) = 02(s)/T(s), for the rotational mechanical system with…

Q: Part 6 Your Answer Use the graphical method to calculate the bending moments at: (a) point C. (b)…

Q: The structure shown is pinned to the floor at A and H. Determine the magnitude of al he support…

A: Consider the FBD shown

Q: 4. In raising the pole from the position shown, the tension T in the cable must supply a…

Q: (a) Figure 4.1 shows a simple pulley system that is used to lift a weight m of 10 kg by application…

A: The mass of the object is m=10 kg The acceleration due to gravity is g=10 m/s2

Q: 5.13 A hydrometer is a device for indicating the specific gravity of liquids. Figure 5.21 shows the…

Q: 4. Helium at 149 kPa absolute and 10°C is isentropically compressed to one-fourth of its original…

A: Answer 4: Given data: P1=149 kPaT1=10°CV2=14V1 Need to determine the final pressure.

Q: 3.42 Two identical metal sheets are formed into tubes with the circular and square cross sections…

Q: Table Q1(a) shows the experimental values for a PVC pipe with diameter of 0.505 m under tensile…

Q: A cylinder with a bore diameter of 1.5 in and a rod diameter of 0.625 in is to be used in a system…

Q: 30 mm 150 mm y 30 mm 150 mm The moment of inertia (in mm) about the axis of symmetry is nearest?

Q: What is the answer in #3B. Show complete solution and FBD

Q: 8 (1) (H) A 1200 kg car driving downhill goes from an altitude of 70 m to 40 m above sea level and…

A: “Since you have posted multiple questions with multiple sub-parts, we will provide the solution only…

Q: A young man, 22 years old, graduated from college and got his first job. He wants to have a…

Q: 5.16 A buoy is to support a cone-shaped instrument package, as shown in Fig. 5.22. The buoy is made…

A: To find: The maximum allowable weight of instrument packages. Given that: Specific weight of buoy is…

Q: Determine the reactions at the supports. 5 kN/m 12 kN Figure 1 4 m 2m 2 m

Q: A vehicle and trailer combination cross a 12-meter bridge with axle loads of 10, 20, and 30 kN…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5…

Q: 27. A cylinder is required to move a 4200 lb load 20 inches in 2 sec- onds. What is the output…

A: Given : force = 4200 lb distance = 20 inches time = 2 sec velocity = distance/time = (20/2) = 10…

Q: 3. A REVERSED CARNOT CYCLE IS USED FOR REFRIGERATION AND REJECTS 200 000 Btu/min OF HEAT AT 152.6F…

A: GIVEN DATA- Q2=200000 Btu/min TH=152.6'F TL=450.6'R WE HAVE TO FIND COP , CAPACITY , WORK

Q: 2. You are working for a glider manufacturer and have been asked to analyse the laminar boundary…

A: For the solution refer below images.

Q: (a) Figure 3.1, shows a ball, of mass m moving on a frictionless track from Point C to Point A which…

A: Write the given data. Circle radius, r=0.4 mInitial velocity, vC=5 m/s at point C.

Q: Consider a brake testing bench as shown in the figure. Motor 16.1 50 20 Clutch + X A motor speeds up…

Q: 12. A cylinder with a bore diameter of 100 mm and a rod diameter of a 40 mm is to be used in a…

Q: A rigid bar, hinged at one end, is supported by two identical springs as shown in figure. Each…

Q: while draining it. What is the rate at which water has to be pumped in so that it gets fully filled…

A: Given, At a constant rate it takes 30 min to empty the half full tank at a constant rate.…

Q: For the figure shown, solve for the maximum value of the counterweight W so that the 2000N block…

Q: The following Brayton cycle is assumed to operate on air with an inlet pressure of 100 kPa, an inlet…

Q: 29. A cylinder with a bore diameter of 50 mm and a rod diameter of 20 mm is to be used in a system…

Q: (a) Plot distance versus time using rectilinear axes. (b) Plot distance versus time on log-log…

A: We need to consider the label of rectilinear axes to draw the graph. Let's consider the x-axis…

Q: 3. Determine the components of force F along the x - y axes which are parallel and perpendicular to…

Q: 9-42. Determine the mass moment of inertia and the radius of gyration about the centroidal wis…

A: Given Mass, m = 64.4 lb Diameter, d = 2 ft Radius, r = 1 ft Fine Mass moment of…

Q: 26. A cylinder is required to move a 150 kN load at a velocity of 0.25 m/s. What is the output…

A: GIVEN DATA- FORCE F=150KN VELOCITY V=0.25 m/s WE HAVE TO CALCULATE THE POWER

Q: (Please note: You should write all your answers to three decimal places.) a) (i) (ii) (iii) F Figure…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: 2 3 6 7 8 9. 10 15 20 25 0.580

A: Solution: The net reading of the vernier caliper is the sum of the main scale reading and the…

Question

can you please find the solution question no:13

КРа.
action
forces?
13. A cylinder with a bore diameter of 3 in and a rod diameter of
1.38 in is required to extend against a load of 15,000 lbs and to
retract against a load of 750 lbs. What pressure is required for
each stroke?
14. A cylinder with a bore diameter of 50 mm and a rod diameter of

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

24 Cast iron is used to make rollers as it has superior compression load. Select one: True False
IS. 03 16. The shaft, as shown in Fig. 14.20, is driven by pulley B from an electric motor. Another belt drive from pulley A is running a compressor. The belt tensions for pulley A are 1500 N and 600 N. The ratio of belt tensions for pulley B is 3.5. B. TA2 A D. TA 150 -100- TB2 100 All dimensions in mm. Fig. 14.20 The diameter of pulley A is 150 mm and the diameter of pulley B is 480 mm. The allowable tensile stress for the shaft material is 170 MPa and the allowable shear stress is 85 MPa. Taking torsion and bending factors as 1.25 and 1.75 respectively, find the shaft diameter. Also find out the dimensions for a hollow shaft with outside diameter limited to 30 mm. Compare the weights of the two shafts. Ans. 30 mm : 24 mm: 1.82]
Find the standard distance between sprocket having 4 in and 16 in diameters.
It is desired to punch a 1.5-in dia. hole through a 1/8-in metal plate which has an allowable stress of 70 psi. What is the minimum force in lb, needed to make the hole?
The figure below shows the components of normal forces, the value of radial force on the gear wheel due to a tangential force of 636 N is N, Take pressure angle as 14½°. ....... af PN Pitch Pt point Gear driven 02 The radial force is
If something is missing then you can assume please solve
B8
1. A four stroke internal combustion engine has the following specifications: Brake power = 7.5 kW; Speed 1000 r.p.m.; Indicated mean effective pressure = 0.35 N/mm2;Maximum gas pressure = 3.5 N/mm2; Mechanical efficiency = 80 %. Determine: 1. The dimesions of the cylinder, if the length of stroke is 1.4 times the bore of the cylin- der; 2. Wall thickness of the cylinder, if the hoop stress is 35 MPa; 3. Thickness of the cylinder head and the size of studs when the permissible stresses for the cylinder head and stud materials are 45 MPa and 65 MPa respectively.
Solve correctly as soon as possible
Please give the proper solution don't copy from online sites I will report.
A 2.5 in diameter by 1.8 in long journal bearing is to carry 5000 lb load at 320 rpm using SAE 40 lube oil at 200 oF through a single hole at 30 psi. Compute the bearing pressure. A. 1111.11 psi B. 142.23 psi C. 123.34 psi D. 197.34 psi Please solve the Problem elaborately. Your solution will be use as reference for my studies. Thank you so much your work will be appreciated much!
.Learning task 3.2 For a No. 7 ball bearing, the New Departure Handbook states that the maximum boreshould be 1.3780 in. and the minimum, 1.3775 in.; for average conditions, the shaftshould have a maximum diameter of 1.3784 in. and a minimum of 1.3779 in.Determine the corresponding tolerances and allowances.