Hot water vapor flows in parallel over the upper surface of a 1-m-long plate. The velocity of the water vapor is 8 m/s at a temperature of 450°C. A copper-silicon (ASTM B98) bolt is embedded in the plate at mid length. The maximum use temperature for the ASTM B98 copper-silicon bolt is 149°C (ASME Code for Process Piping, ASME B31.3-2014, Table A-2M). To devise a cooling mechanism to keep the bolt from getting above the maximum use temperature, it becomes necessary to determine the local heat flux at the location where the bolt is embedded. If the plate surface is kept at the maximum use temperature of the bolt, what is the local heat flux from the hot water vapor at the location of the bolt? Given that the properties of water vapor at the film temperature of Tf 300°C are (Table A-16) Pr = 0.9401, k = 0.04345 W/m-K, and v= 5.340 x 10-5 m²/s. Water vapor Too = 450°C Bolt T₁ The local heat flux from the water vapor at the location where the bolt is embedded is W/m²

Hot water vapor flows in parallel over the upper surface of a 1-m-long plate. The velocity of the water vapor is 8 m/s at a temperature of 450°C. A copper-silicon (ASTM B98) bolt is embedded in the plate at mid length. The maximum use temperature for the ASTM B98 copper-silicon bolt is 149°C (ASME Code for Process Piping, ASME B31.3-2014, Table A-2M). To devise a cooling mechanism to keep the bolt from getting above the maximum use temperature, it becomes necessary to determine the local heat flux at the location where the bolt is embedded. If the plate surface is kept at the maximum use temperature of the bolt, what is the local heat flux from the hot water vapor at the location of the bolt? Given that the properties of water vapor at the film temperature of Tf 300°C are (Table A-16) Pr = 0.9401, k = 0.04345 W/m-K, and v= 5.340 x 10-5 m²/s. Water vapor Too = 450°C Bolt T₁ The local heat flux from the water vapor at the location where the bolt is embedded is W/m²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A liquid is entering a 10 m long pipe of 0.2 m diameter at 25°C with an average velocity of 0.02 m/s. The pipe is kept at a constant surface temperature of 40°C. Assume the flow is both hydrodynamically and thermally fully-developed in the pipe. Find out the outlet temperature. Justify if the assumption of fully-developed flow is appropriate. The properties of the fluid can be assumed constant with following values Density: 484.2 kg/m³; Specific heat capacity: 2802 J/kg.K; Thermal conductivity: 0.0904 W/m.K; Dynamic viscosity: 9.197 × 10-5 kg/m.s; Prandtl number: 2.85. 29.3 °C
Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cm-ID tube whose surface is maintained at 620 K. What length of tube is required?
Heat Transfer Questiion is image
Air is flowing at 35°F with a velocity of 12 ft/s over a plate 10 ft long and 2 ft wide. The plate is at room temperature. Determine the coefficients of local friction, heat transfer coefficient and heat transfer rate of the plate at 1 ft intervals along the length. Plot on the same graph the results as a function of distance from the leading edge, the graph will be reviewed. The table of thermal properties of air is on the platform. Report in the following boxes your results for a length of 5 ft.
The sensible heat-transfer coefficient for a dry surface has been determined to be 50 W/(m2-C) at a certain Reynolds number. Estimate the total heat transfer to the surface per unit area at a location where the wall temperature is 10 C and the state of the moist air flowing over the surface is given by 24 C dry bulb and 18 C wet bulb. Assume that the Reynolds number does not change and the Lewis number is 0.82. Assume that the condensate present on the surface will increase the transfer coefficients by about 15 percent
Heat transfer
6-34 Liquid ammonia at 10°C and 1 atm flows across a horizontal cylinder at a velocity of 5 m/s. The cylinder has a diameter of 2.5 cm and length of 125 cm and is maintained at a temperature of 30°C. Calculate the heat lost by the cylinder. 6-65 Water flows over a 3-mm-diameter sphere at 5 m/s. The free- stream temperature is 38°C, and the sphere is maintained at 93°C. Calculate the heat-transfer rate. 6-95 A tube bank consists of a square array of 144 tubes arranged in an in-line position. The tubes have a diameter of 1.5 cm and length of 1.0 m; the center-to-center tube spacing is 2.0 cm. If the surface temperature of the tubes is maintained at 350 K and air enters the tube bank at 1 atm, 300 K, and u∞ = 6 m/s, calculate the total heat lost by the tubes.
Hot water is flowing though the center of a AISI 304 stainless steel pipe with a diameter of 300mm, a wall thickness of 10mm and a length of 5m. The pipe is coated with a 2.5mm thick layer of Teflon and covered with a 30mm thick layer of insulation. The water is flowing at a velocity of 0.0015 m/s. Assume the velocity profile to be fully developed. The water is at a temperature of 92°C and the air surrounding the pipe is at 22°C. Some transport properties and dimensions are shown in the table below. 1. What is the heat transfer rate through the pipe and insulation? 2. What is the heat flux at the inner pipe surface and the outer surface of the insulation? 3. What is the temperature of the outer surface of the insulation? Insulation Pipe Too water Uwater Teflon Tm air hair Pipe inner diameter: 300mm Pipe wall thickness: 10mm Teflon Layer thickness: 2.5mm Insulation thickness: 30mm Length: 5m To, water: 92°C Lair: 22°C hair: 75 W/m2/K k30455: 15.2 W/m/K kTeflon: 0.38 W/m/K kinsulation:…
Evaluate the convection heat transfer coefficient for the flow of (a) air and (b) water at a velocity of 5 m/s in an 8-cm-diameter and 10-m-long tube when the tube is subjected to uniform heat flux from all surfaces. Use fluid properties at 25° C and assume fully developed turbulent flow in the entire duct.
Laminar flow normally persists on a smooth flat plate until a critical Reynolds number value is reached. However, the flow can be tripped to a turbulent state by adding roughness to the leading edge of the plate. For a particular situation, experimental results show that the local heat transfer coefficients for laminar and turbulent conditions are hlam (x) = Alamæª htur (x) - Aturæb Alam = 1.98 a = -0.5 Atur = 4.15 b = -0.3 Calculate the average heat transfer coefficients for laminar and turbulent conditions for plates of length L = 0.2 m and 2.5 m.
Water at 25 °C is flowing at a velocity of 0.45 m/s in a tube having a mass transferarea (Black region in the figure) of 4.42.10-5 m2. The tube is 1.2 m long with the walls coatedwith formic acid. The solubility of formic acid in water is 100000 mg/L. Viscosity of water is8.71 x 10-4 Pa.s and the density of water is 996 kg/m3. Assuming that the velocity profile is fullydeveloped.a. Determine the flow type.b. Calculate the convective mass-transfer coefficient k'c.c. Calculate the flux of NA.
2. Consider airflow over a plate surface maintained at a temperature of 215°C. The temperature profile of the airflow is given as T(y) = Too (Too - T,) exp (- V fluid The airflow at 1 atm has a free stream velocity and temperature of 5 cm/s and 25°C, respectively. Determine the heat flux on the plate surface and the convection heat transfer coefficient of the airflow.