Air at 298 K and 1 atm laden with acid fog is led from a process to square horizontalsettling chamber of 8 m long and 50 cm high. The fog consists of spherical droplets ofdiameter 0.8 mm and density 1 g cm-3. Determine the volumetric flow rate in m³ hr-1which will allow 90% removal of the fog from the stream.

Air at 298 K and 1 atm laden with acid fog is led from a process to square horizontal settling chamber of 8 m long and 50 cm high. The fog consists of spherical droplets o diameter 0.8 mm and density 1 g cm-3. Determine the volumetric flow rate in m³ hr¯!

Air at 298 K and 1 atm laden with acid fog is led from a process to square horizontal settling chamber of 8 m long and 50 cm high. The fog consists of spherical droplets o diameter 0.8 mm and density 1 g cm-3. Determine the volumetric flow rate in m³ hr¯!

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For steady-state, one-dimensional flow of a compressible fluid in a varying cross-sectional area, prove that: dp PM² 1 dA A 1-M²
A dimensionless group on which its application is on pressure and momentum in fluid
Question- In a laminar flow between two parallel plates with a separation distance of 6 mm, the centre line velocity is 1.8 m/s. The velocity (in m/s) at a distance of 1 mm from the Boundary is
Compare the capillary effect of immersion in (i) water and (ii) mercury of a glass tube of 6 mm internal diameter. The surface tension values are 0.072500 N/m and 0.60 N/m for water and mercury. The angle of contact for water is zero degree. The angle of contact for mercury is 130°
Water flows at 5m/s is passed through a tube of 2.5 cm diameter, it is found to be heated from 20 °C to 60 °C. The heating is achieved by condensing steam on the surface of the tube and subsequently the surface temperature of the tube is maintained at 90degC. Water properties are as follows: density=995kg/m3, kinematic viscosity=.657x10-6 m2/s, Pr=4.43, k=.628W/mK, cp=4178J/kgK. a) Determine the Reynolds number b) What is the thermal coefficient on question number c) what is the heat absorbed by the water?
Please help class is heat transfer, will rate question. Show all steps and equations used, thank you.
Steady flow of fluid is also known as (write in small letters). In viscous flow there is no fluid friction. Answer:
H.W.2 /: Consider a 55cm long journal bearing that is lubricated with oil whose viscosity is 0.1 kg/m.s at 20°C at the beginning of operation and 0.008 kg/m.s at the anticipated steady operating temperature of 80°C. The diameter of the shaft is 8 cm, and the average gap between the shaft and the journal is 0.08 cm. Determine the torque needed to overcome the bearing friction initially and during steady operation when the shaft is rotated at 1500 rpm?
A cylinder 1 inch in diameter is placed in a hot water pipe at right angles to the direction of theflow. The fluid and cylinder temperatures are at 80 °F and 100 °F respectively. Calculate thevalue of the film coefficient for a mass flow of 2705 lb/hr.
A 0.10-mm-diameter glass tube is inserted into water at 100°C in a tub to observe capillary rise phenomenon. Determine the capillary rise of water in the tube. (a) What would happen if water is replaced with gasoline in tube? (b) Can you calculate the capillary rise if the diameter of tube at one end is 0.3mm and on the other end it is 0.10mm
What is mechanical pressure Pm, and how is it used in an incompressible flow solution?
8- Air (p = 1.21 kg/m') flows over a thin flat plate 1 m long and 0.3 m wide. The flow is uniform at the leading edge of the plate. Assume the velocity profile in the boundary layer is linear, and the free stream velocity is 2.7 m/s. Using control volume (abcd) shown in figure, compute the mass flow rate across surface (ab). Determine the magnitude and direction of the x- component of the force required to hold plate stationary. [3.9×10 kg/s ; -3.5x10 N]