Hot engine oil at 150°C is flowing in parallel over a flat plate at a velocity of 2 m/s. Surface temperature of the 0.5-mlong flat plate is constant at 50°C. Determine (a) the local convection heat transfer coefficient at 0.2 m from the leading edge and the average convection heat transfer coefficient, and (b) repeat part (a) using the Churchill and Ozoe (1973) relation.

Hot engine oil at 150°C is flowing in parallel over a flat plate at a velocity of 2 m/s. Surface temperature of the 0.5-mlong flat plate is constant at 50°C. Determine (a) the local convection heat transfer coefficient at 0.2 m from the leading edge and the average convection heat transfer coefficient, and (b) repeat part (a) using the Churchill and Ozoe (1973) relation.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.38P

See similar textbooks

Related questions

Q: A hot plate 1.2 m wide, 0.35 m high and at 115 0C is exposed to the ambient still air at 25 0C.…

A: Write the expression for the kinematic viscosity of air. Here, μ represents the dynamic viscosity…

Q: Air at atmospheric pressure and 27 degree celsius is blown across a long 4.0-cm diameter tube at a…

A: Solution:

Q: Hot exhaust gases leaving a stationary diesel engine at 450°C enter a l5-cm-diameter pipe at an…

A: Given data as per the question The temperature of gasses at the exit of engine =4500c Diameter of…

Q: Hot air at atmospheric pressure and 80°C enters an 8-m-long uninsulated square duct of cross-…

Q: A long 9 cm-diameter steam pipe whose external surface temperature is 70 0C passes through some open…

Q: Consider the flow of oil (use unused engine oil properties) at 20? in a 30-cm-diameter pipeline at…

A: Solution:

Q: A long 10-cm-diameter steam pipe whose external surface temperature is 110°C passes through some…

A: In order to proceed with the problems some assumptions need to be considered. Steady operating…

Q: ir at 3*10-4 kg/s and 27°C enters a rectangular duct that is 1 m long and 4 mm x 16 mm on the sides.…

A: Given: m˙ = 3×10-4 kg/s Tm,i=27oC=300K L =1 m W = 16mm=0.016m h = 4mm=0.004m qs˙= 600 W/m2

Q: During a cold winter day, wind at 55 km/h is blowing parallel to a 4m high and 10m long wall of a…

Q: Consider an airplane cruising at an altitude of 10 km where Standard atmospheric conditions are…

A: Given dataDimensions Lxw=25x3H=10 kmV=800 kmhCf=0.001bP=26.5 KPaT=-50°C

Q: EES Metal plates (k = 180 W/m-K, p= 2800 kg/m², |and c, = 880 J/kg-K) with a length of 1 m and a…

Q: A computer circuit board dissipates 0.1 KW from one side over an area 300 mm by 200 mm. A small…

Q: A 15-cm-diameter horizontal cylinder has a surface temperature that is maintained at 120°C. Water at…

A: Given:Diameter of a cylinder, D=15 cm=0.15 mSurface temperature of the cylinder, Ts=120oCWater…

Q: Consider a 10-m-long smooth rectangular tube, with a = 50 mm and b = 25 mm, that is maintained at a…

A: Nusselt number signifies the Convective resistance over the conductive resistance It is used to…

Q: Liquid mercury at 250°C is flowing with a velocity of 0.3 m/s in parallel over a 0.1-m-long flat…

A: The data given is, The temperature of liquid Mercury = 250 ℃ The velocity of flow, V = 0.3 m/s…

Q: A pure copper cube 3 cm on each side is placed in a 15°C stream of water.If the initial temperature…

Q: Consider a 10-m-long smooth rectangular tube, with a= 50 mm and b= 25 mm, that is maintained at a…

Q: An average person body surface is approximately 2.0 m². Its skin temperature is 33°C. The convection…

A: Find convective heat transfer .

Q: Air is flowing in parallel over the upper surface of a flat plate with a length of 4m. The first…

A: Heat supplied is the heat supplied for power generation or for the useful work of a machine. This…

Q: Determine the convection heat transfer coefficient (in W/m²·K) for air flowing at a velocity of 3…

Q: Hot water at an average temperature of 80°C and an average velocity of 1.5 m/s is flowing through a…

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: C flows through an automob velocity of 1 m/s. The surfac ficient using Colburn Analog factor f=…

Q: Air is flowing in parallel over the upper surface of a flat plate with a length of 4 m. The first…

A: The velocity of free stream is V=0.5 m/s. The temperature of air is T∞=100C. The kinematic viscosity…

Question

Hot engine oil at 150°C is flowing in parallel over a flat
plate at a velocity of 2 m/s. Surface temperature of the 0.5-mlong
flat plate is constant at 50°C. Determine (a) the local
convection heat transfer coefficient at 0.2 m from the leading
edge and the average convection heat transfer coefficient,
and (b) repeat part (a) using the Churchill and Ozoe (1973)
relation.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is . Under these conditions, the average Nusselt number was found to be equal to 4150. Determine the average heat transfer coefficient for an oil having thermal properties similar to those in Appendix 2, Table 18, at at the same Reynolds number and flowing over the same plate.
i need the answer quickly
Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates as shown in Fig 3. The gas at 220°C flows in parallel over the upper and lower surfaces of a 2-m-long flat plate at a velocity of 2 m/s. If the flat plate srface temperature is maintained at 80°C, de termine the local convection heat transfer coefficient at 1 m from the leading edge, the average convection heat transfer rate over the e ntire plate, and the total heat flux transfer to the plate. 11. 111. COo, T. Fig 3
Please help with this questionHot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. Thegas at 220°C flow is parallel over the upper and lower surfaces of a 3-m-longflat plate at a velocity of 3 m/s. If the flat plate surface temperature ismaintained at 80°C.Determine the local convection heat transfer coefficient at 1 m fromthe leading edge and calculate the average convection heat transfer coefficient over theentire plate.
Determine the convection heat transfer coefficient (in W/m2-K) for air flowing at a velocity of 3 m/s in a 10-cm diameter and 10-m long tube. Air enters the tube at 10°C and leaves at 20°C, i.e. air is heated. Take the property of air at 1 atm and assume flow to be fully developed. For air at 1 atm: Temperature k, W/m-K v, m?/s Pr 15°C 0.02476 1.470x10-5 0.7323 20°C 0.02514 1.516x10-5 0.7309 25°C 0.02551 1.562x10-5 0.7296 Hint: When the fluid temperature changes, we use its properties at mean temperature, unless otherwise specified. Round your answer to 2 decimal places.
Determine the convection heat transfer coefficient (in W/m²-K) for air flowing at a velocity of 3 m/s in a 10-cm diameter and 10-m long tube. Air enters the tube at 10°C and leaves at 20°C, i.e. air is heated. Take the property of air at 1 atm and assume flow to be fully developed. For air at 1 atm: Temperature k, W/m-K v, m?/s Pr 15°C 0.02476 1.470x105 0.7323 20°C 0.02514 1.516x10-5 0.7309 25°C 0.02551 1.562x105 0.7296 Hint: When the fluid temperature changes, we use its properties at mean temperature, unless otherwise specified. Round vour answer to2 decimal nlaces
Determine the convection heat transfer coefficient (in W/m2-K) for air flowing at a velocity of 3 m/s in a 10-cm diameter and 10-m long tube. Air enters the tube at 10°C and leaves at 20°C, i.e. air is heated. Take the property of air at 1 atm and assume flow to be fully developed. For air at 1 atm: Temperature k, W/m-K v, m?/s Pr 15°C 0.02476 1.470x10-5 0.7323 20°C 0.02514 1.516×10-5 0.7309 25°C 0.02551 1.562x105 0.7296
Determine the convection heat transfer coefficient (in W/m2-K) for air flowing at a velocity of 8 m/s in a 10-cm diameter and 10-m long tube. Air enters the tube at 30°C and leaves at 20°C, i.e. air is cooled. Take the property of air at 1 atm and assume flow to be fully developed. For air at 1 atm: Temperature k, W/m-K v, m?/s Pr 15°C 0.02476 1.470x10-5 0.7323 20°C 0.02514 1.516x10-5 0.7309 25°C 0.02551 1.562x10-5 0.7296 Hint: When the fluid temperature changes, we use its properties at mean temperature, unless otherwise specified. Round your answer to 2 decimal places. Add vour answer
Determine the convection heat transfer coefficient (in W/m?.K) for air flowing at a velocity of 3 m/s in a 10-cm diameter and 10-m long tube. Air enters the tube at 10°C and leaves at 20°C, i.e. air is heated. Take the property of air at 1 atm and assume flow to be fully developed. For air at 1 atm: Temperature k, W/m-K v, m?/s Pr 15°C 0.02476 1.470x10-5 0.7323 20°C 0.02514 1.516x10-5 0.7309 25°C 0.02551 1.562x105 0.7296 Hint: When the fluid temperature changes, we use its properties at mean temperature, unless otherwise specified. Round your answer to 2 decimal places.
Determine the convection heat transfer coefficient (in W/m²-K) for air flowing at a velocity of 3 m/s in a 10-cm diameter and 10-m long tube. Air enters the tube at 10°C and leaves at 20°C, i.e. air is heated. Take the property of air at 1 atm and assume flow to be fully developed. For air at 1 atm: Temperature k, W/m-K V, m²/s Pr 15°C 0.02476 1.470×105 0.7323 20°C 0.02514 1.516x10-5 0.7309 25°C 0.02551 1.562x10-5 0.7296 Hint: When the fluid temperature changes, we use its properties at mean temperature, unless otherwise specified.
Water at 43.3°C flows over a large square plate at a velocity of 28 cm/s. The plate is 1.2 m long (in the flow direction) and its surface is maintained at a uniform temperature of 10.0°C. The width of the plate is 1.2 m. Calculate the steady rate of heat transfer for the entire width of the plate in watts (W). The properties of water at the film temperature of (Ts + T∞)/2 = (10 + 43.3)/2 = 27°C are ρ = 996.6 kg/m3, k = 0.610 W/m·°C, μ = 0.854 × 10–3 kg/m·s, and Pr = 5.85. The steady rate of heat transfer per unit width of the plate is ___ W.
mperature of nermocouple kg/m³, and an ideal gas 7-94 The components of an electronic system are located in a 1.5-m-long horizontal duct whose cross section is 20 cm x 20 cm. The components in the duct are not allowed to come into direct contact with cooling air, and thus are cooled by air at 30°C flowing over the duct with a velocity of 200 m/min. If the surface temperature of the duct is not to exceed 65°C, determine the total power rating of the electronic devices that can be mounted into the duct. 7-97 flow If the initial is cor evaluate the 0.3 m of the initial cities of the 3D to the transt perform the from 1 to Treat me and the free stream Electronic o determine components inside 9 percent of tion of this 30°C 200 m/min 65°C Air 1.5 m on 20 cm FIGURE P7-94