he shafts are made of steel with shear modulus of 75 GPa. Determine the angle of twist of gear B if a torque of 30 kN·m is applied to gear B. Both shafts have the same diameter of 90 mm. (Hint: for the meshing cylindrical gears, i.e. gear C and D, the angle of twist need to time the radius of the gear while applying the equation of compatibility.

he shafts are made of steel with shear modulus of 75 GPa. Determine the angle of twist of gear B if a torque of 30 kN·m is applied to gear B. Both shafts have the same diameter of 90 mm. (Hint: for the meshing cylindrical gears, i.e. gear C and D, the angle of twist need to time the radius of the gear while applying the equation of compatibility.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A parallel shaft helical gear consists of a 20 dts drive pinion And a 96 driven gear. Both gears have a transverse diametrical pitch of 20 dts / in, a helix angle of 25 and a pressure angle on = 20 . The face width is 4 in., AND the gears are moving at 1600 ft / min, on the pitch line. The impeller is made of steel UNSG 10180 CD and without heat treatment; the driven one is made of grade 30 cast iron. Based on flexural strength calculations, evaluate the capacity or safe maximum power at hp. Consider general industrial service, and nG = 4.
Each of two gears in a mesh has 60 teeth and a module of 6 mm. The teeth are of involute profile. The arc of contact is 2.5 times the circular pitch. Determine the addendum
The top half of a compound Epicyclic gearset is shown in Figure, with input shaft I rotating at a constant speed of 700 rpm in a clockwise direction and generating 12 kW input power. The Annulus wheel A2 isform a compound wheel with gear O and connected to an auxiliary gear N on shaft X. . The Annulus A1 rotates in a counter-clockwise direction at a speed of 5,300 rpm. Calculate the following using this condition: The speed and direction of output shaft O (NO), shaft X (NX) and gear ratio (n). If Annulus wheel A1 is locked calculate the speed and direction of output shaft O (NO), shaft X (NX) and gear ratio (n). The braking torque (Tb) (magnitude and direction) that must be applied to Annulus wheel A1 to hold it stationary, assuming gear transmission efficiency is 90%. Number of gear teeth:P1 = 30 , A1 = 120P2 = 50 , A2 = 140N = 60 , O = 120
In a compound epicyclic gear train, has gears A and an annular gears D & E free to rotate on the axis P. B and C is a compound gear rotate about axis Q. Gear A rotates at 75CCW rpm CCW and gear D rotates at 390CW rpm CW. Find the speed and direction of rotation of arm F and gear E. Gears A, B and C are having 16, 45 and 21 teeth respectively. All gears having same module and pitch. Sketch the arrangement and solve by tabular column method.
Please help
Gears Two 20-pitch, 14.5°, full-depth, involute spur gears are used on a machine shop lathe. The pinion has 16 teeth and the gear has 70 teeth. Determine the following: Q5.a The centre distance Q5.b The contact ratio Q5.c Whether interference is a problem Q5.d A centre distance that reduces backlash from a vendor value of 0.4/Pd to an AGMA recommended value of 0.1/Pd
please help solve
In a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast iron profile. The diametral pitch is 6-teeth/in, the face width si 0.5 inches, and the pressure angle is 20 degrees. Assume that the pinion transmits 10 hp at a speed of 2000 rpm. Find the pitch diameters of the gears. Find the pitch line velocity in ft/min Find the velocity factor Ky Find the tangential load in lbf Find the contact stress in kpsi, assuming CP=1960 psi.
5.3 Please help. Provide Free Body Diagram, labeled with appropriate quantities to better understand. Also solve. Thank you.
Three 14.5° pressure angle spur gears with a diametral pitch of 8 are meshed. The input pinion on the left is running clockwise at 3101 rpm and transmits 3.2 Hp. Gear 1 (Pinion) Input N1 = 20 teeth Gear 2 Idler Gear 3 Output N3 = 25 teeth N2 = 75 teeth Answer the following: 1. Pinion (Gear 1) pitch diameter (1 mark) 2. Gear 2 pitch diameter (1 mark) 3. Gear 3 pitch diameter (1 mark) 4. Circular pitch (1 mark) 5. Addenda (1 mark) 6. Center distance from gear 1 to gear 3 (2 marks) 7. Line of action length for gear 1 contacting gear 2 (2 marks) 8. Contact ratio of gear 1 and 2 (2 marks) 9. Gear ratio from gear 1 to gear 3 (1 mark) 10. Draw a free-body diagram of Gear 2, showing the radial and tangential forces. Calculate these forces. What is the reaction force in the bearing? (3 marks)
The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
1 %00 llı. In. اسئلة مقاومة المواد ال. . اسئلة مقاومة المواد Q-1 The gears attached to the fixed -end steel shaft are subjected to the torques shown in fig .The shaft has diameter of (14 mm ).Determine the max shear stress and the angle of twist A relative c. use G=80 Gpa 280 N.m A 150 N.m 40 N.m 0.4m 0.3m 0-2 Draw the shear and moment diagram for the beam loaded shown in fig 15 KN 80 KN .m 5 KN/m 5 m 5m II