Determine the maximum torque that can be applied to a hollow circular steel shaft of 100mm outer diameter and 80mm inner diameter. The shear stress is limited to 70 MPa, and the angle of twist must not exceed 0.4 degrees in a length of one meter. Use G = 83 GPa for steel.

Q: A solid shaft in a rolling mill transmits a torque of 1600 N.m. Determine the diameter of the shaft…

A: Given Data T=1600 N.m = 16×105 N.mm Max. Shear stress=40 MPa Angle of twist=8° L=2500 mm G=83 GPa

Q: Determine the angle of twist caused by a 25kip – in torque T in the 3in diameter solid aluminium…

A:

Q: What is the minimum diameter of a solid steel shaft that will not twist through more than 6° in a…

A:

Q: A solid shaft with a yield strength of 500 MPa subjected to a torque of 60N.m and bending moment of…

A: Step 1: Given data:Yield strength, σy​=500MPaTorque, T=60N.mBending moment, M=70N.mStep 2: We need…

Q: must transmit the torque of 34 kN-m. The total angle of twist must not exceed 3°. The maximum…

A:

Q: A hollow circular steel shaft with an outside diameter of 2.906. and a wall thickness of 0.437 in.…

A:

Q: L1=1.8 L2=.9 d1=70 d2=53 Compound shaft ACB is fixed at A and consisting of two solid circular…

A: Given data:-diameter, d1=70mm & diameter, d2=53mmLength, L1=1.8m=1800mm &…

Q: e maximum shear stress developed

A: Need to calculate maximum shear stress .

Q: A circular solid shaft made of vibranium has G=80 MPa and has a limiting torsional shear stress of…

A:

Q: À solid 0.96-in.diameter shaft is subjected to the torques shown. The bearings shown allow the shaft…

A:

Q: Two designs for a shaft are being considered. Both have an outside diamete of 80 m and are 100 cm…

A:

Q: What torque can be applied to the composite shaft without.

A: Given data, aA hollow bronze shaftThe outer diameter D= 75 mm= 0.075mthe inner diameter d= 50 mm=…

Q: Shafts A and B are made of the same material and have the same cross-sectional area, but A has a…

A:

Q: The composite shaft of total length is 1.8 m consists of 5 mm thick brass and is fixed to a 30 mm…

A:

Q: The 60-mm-diameter shaft is made of 6061-T6 aluminum. (Figure 1) Figure Part A If the allowable…

A: Givend=60mmτallow=80MPaθA/Callow=0.060 rad

Q: A 50-mm diameter solid shaft, with a length of 1 meter, is supported at one end and free in the…

A: following is the solution for the above problem-

Q: Determine the torque in ft-Ib that can be applied to a 1-in diameter circular shaft if the shearing…

A: According to the given data τ=8000 Psi D=1 in  We need to find The torque in ft-Ib that can be…

Q: A hollow steel shaft is stressed to 55 MPa by a torque of 100,000 ft-lb. If the inside diameter is…

A:

Q: A hollow steel shaft with an outside diameter of 80 mm and a wall thickness of 11 mm is subjected to…

A:

Q: What is the minimum diameter of a solid steel shaft that will not twist through more than 3° in a 6…

A:

Q: A propeller shaft in a ship is 400 mm in diameter and 6 m in length. The allowable shearing stress…

A: Given data Diameter of shaft = D = 400 mmLength of shaft = L = 6 mAllowable shearing stress = τ = 60…

Q: Find out the outer diameter of the hollow shaft, if the allowable shear stress induced in it is…

A: Data given-  Allowable shear stress = 53 MPa  Permissible value of torque = 2000 N-m  K = di /do =…

Q: A steel shaft 2ft long that has a diameter of 4in. is subjected to a torque of 12kip-ft. Determine…

A:

Q: An aluminum shaft of two segments is shown below. Determine the allowable torque if the shear stress…

A: Given Data Diameter of bar AB is : d1=90 mm Diameter of bar BC is : d2=60 mm Allowable stress is :…

Q: aft with a hollow cross section is subjected to torque of magnitude T = 5.5 kN-m. If the outer…

A: Given:T=5.5 kN.mdo=0.1 mt=10 mm

Q: SETB: A steel shaft 3 ft long that has a diameter of 4 in. is subjected to a torque of 15 kip.ft.…

A:

Q: Two pipes were connected by a flanged bolt coupling. The material properties are as follows: For…

A:

Q: A hollow steel shaft with an outside diameter of 62 mm and a wall thickness of 6 mm is subjected to…

A: Given that ,  Outside diameterDo=62mmThicknesst=6mmPure torqueτ=7300N-mShear modulusG=73GPaLength of…

Q: 1) What is the minimum diameter of a solid steel shaft that will not twist through more han 3º in a…

A: Given that ,  Length l=6 m Torqueτ=14kNmG=83GPaTwist angle θ=3°

Q: A hollow cylindrical shaft has outer diameter of 115 mm and inside diameter of 75 mm. Determine the…

A:

Q: A compound steel (G= 70 GPa) shaft consists of a solid 59-mm-diameter segment (1) and a solid 39-mm-…

A:

Q: A flywheel is to be fitted on a punching machine with 73% mechanical efficiency. The machine makes…

A: Write the given data in the problem. n=20 strokes/mind=20 mm t=12 mmη=73% τ=330 MPa Here, n is the…

Q: The driveshaft of an automobile is being designed to transmit 234 kw at 3167 rpm. Determine the…

A:

Q: 1. A solid aluminum shaft 4 m long that has a diameter of 120 mm is subjected to a torque of…

A:

Q: solid steel shaft must not twist through more than 3° in a 6-m length when subjected to a torque of…

A:

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.