Shafts A and B are made of the same material and have the same cross-sectional area, but A has a circular cross section and B has a square cross section. Determine the ratio of the maximum torques TA and Tg when the two shafts are subjected to the same maximum shearing stress (TA=TB). Assume both deformations to be elastic. Refer to Table 3.1. A B TB The ratio of the maximum torques is TA/TB=

Shafts A and B are made of the same material and have the same cross-sectional area, but A has a circular cross section and B has a square cross section. Determine the ratio of the maximum torques TA and Tg when the two shafts are subjected to the same maximum shearing stress (TA=TB). Assume both deformations to be elastic. Refer to Table 3.1. A B TB The ratio of the maximum torques is TA/TB=

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.2P: A circular steel tube with an outer diameter of 75 mm and inner diameter of 65 mm is subjected to...

See similar textbooks

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
A circular steel tube with an outer diameter of 75 mm and inner diameter of 65 mm is subjected to torques 7"at its ends. Calculate the maximum permissible torque 7jliajl if the allowable normal strain is ea= 5 X 10"4 Assume that G = 15 GPa.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
Figure 2 shows a solid shaft consisting of two prismatic circular parts in equilibrium under the torques applied to the pulleys fastened to it. Give that the diameter for part AB and BC are 200 mm and 120 mm, respectively. (a) Determine the torque, TR on the shaft. (b) State the segment at which the maximum shearing stress occurs. Verify your answer by shear stress analysis. d- 200 mm d- 120 mm TA= 36 kN.m Te=14 kN.m Ta C Figure 2: Solid shaft with pulleys
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
Two pipes were connected by a flanged bolt coupling. The material properties are as follows: For outer bolts, 12 pieces, 16 mm diameter, on a mean radius of 150 mm, G = 28 GPa. For the inner bolts, 8 pieces, 12 mm diameter, on a mean radius of 100 mm, G = 20 GPa. Determine the total torque of the system if the shearing stress is limited to 30 MPa in the bolts. (Draw also the FBD) with complete solution
Question 4. The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at 4, and a torque of T= 50 kN.m is applied to it at C, determine the angle of twist that occurs at C and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst 115 GPa, Gbr 56 GPa. 3 m %D 2 m 100 mm 50 mm T= 50 kN. m
Part A The solid shaft cross-sections shown are subjected to the externally applied torques shown. Compare the corresponding shear stresses developed in each shaft at point P. P P 2 T Rank the solid shafts from the largest shear stress at P to the smallest shear stress at P. (For example, 4> 3 = 1 > 2). 0.5 T
2. An implant is made of a titanium alloy having an allowable shear stress of tallow = 50 MPa. If the diameter of the implant is 120 mm, determine the maximum torque T that can be transmitted. What would be the maximum torque T' if an 80-mm-diameter hole were bored through the implant? 1S T (Answer: T =16.96 kN.m; T'=13.613 kN.m)
Only answer A2 please