The motor delivers 65 hp to the A36 steel shaft while it rotates at 1500 RPM.  The shaft is supported on smooth bearings at B and E, which allow free rotation of the shaft.  The gears C and D fixed to the shaft remove 70% and 30% of the power delivered by the motor, respectively.  Determine the diameter of the shaft to the nearest 1/8 in. if the allowable shear stress is ττallow = 12 ksi and the allowable angle of twist of D with respect to A is 0.25 degrees.

Q: The turbine develops 150 kW of power, which is transmitted to the gears such that C receives 70% and…

A: Given:- power p=15 KW                  diameter d=100mm=0.100m                  speed N=800 rpm…

Q: 1000 Nom 1060Nom TITTITIIT

A:

Q: The shaft is made of A-36 steel, has a diameter of 95 mm, and is fixed at B while A is loose and can…

A: Write the given data.

Q: The drive shaft of the motor is made of a material having an allowable shear stress of τallow= 72…

A:

Q: The splined ends and gears attached to the A992 steel shaft are subjected to the torques. The shaft…

A: Diameter of the shaft (D)= 50 mmFor the A992 steel shaftthe value of the shear modulus is G=75Gpa

Q: The drive shaft of the motor is made of a material having an allowable shear stress of τallow= 72…

A:

Q: If end B of the shaft, which has an equilateral triangular cross-section, is subjected to a torque…

A: Given data as per question Torque = 900 lb.ft Assuming G of the shaft = 3.7×103 ksi

Q: 300 N-m 500 N-m The solid 30-mm-diameter shaft is used to 200 N-m transmit the torques applied to…

A: It is required to determine maximum shear stress

Q: Part A Determine the maximum shear stress in shaft BD. Express your answer to three significant…

A:

Q: 10-6. The solid 30-mm-diameter shuft is used to transmit the torques applied to the gears. Determine…

A: Given data: The diameter of the shaft is; d=30 mm.   Draw the free body diagram of the shaft.…

Q: The A-36 steel shaft with a diameter of 30mm is supported on smooth bearings that allow it to rotate…

A: Given: The diameter of the shaft, d = 30 mm = 0.03 m The modulus of elasticity of the A36 shaft, G =…

Q: The drive shaft of a car is designed to be a tube with an outer diameter of 4 in. The engine…

A: Given the following data:Outer diameter of the shaft, do= 4inPower delivered by the engine, P= 190hp…

Q: The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown.…

A: Given data: The diameter of the shaft is d=40 mm. The material of the shaft is A992. The modulus…

Q: The gear motor can develop 14 hp when it turns at 600 rev>min. If the shaft has a diameter of 12…

A: Given Data: The power developed by the motor is P = 14 hp. The number of revolutions is N = 600…

Q: The composite shaft consists of a mid-section that includes the 1-in. diameter solid shaft and a…

A:

Q: The shaft has an outer diameter of 1.5 in. and an inner diameter of 0.8 in. If it is subjected to…

A:

Q: The shear modulus of the solid steel shaft is G = 11 x 10° ksi. Motor A is directly coupled to the…

A: Write the given data with suitable variables. G=11×103 ksi=11×106 psiPM=3 hpN=1800 rpmζallow=9…

Q: The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown where…

A: Given:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.