The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown where T = 140 N-m. 1200 N m 400 N m 600 N m 600 mm 500 mm 400 mm Tap image to zoom The shaft has a diameter of 30 mm. Part A Determine the angle of twist of end B with respect to end A. Express your answer to three significant figures and include appropriate units.

The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown where T = 140 N-m. 1200 N m 400 N m 600 N m 600 mm 500 mm 400 mm Tap image to zoom The shaft has a diameter of 30 mm. Part A Determine the angle of twist of end B with respect to end A. Express your answer to three significant figures and include appropriate units.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please help ASAP. Help with part A-B Provide Free Body Diagram, labeled with appropriate quantities to better understand.Thank you
Please don't provide handwrittenh solution.
Please hel me solve this asap. Thank you!!
An electric motor develops 6 HP at 3000 rpm. An 18 tooth gear is fitted to its shaft to drive a gear on an output shaft. How many teeth would be needed on this output gear if an output torque of 100 Nm is required? Answer: Ti vious page Next page https://learnonline.gmit.ie/mod/quiz/attempt.php?attempt-126637&cmid-1429658page-3# CHao Search for anything FI1 F10 F8 F9
NEED DETAILED ANSWER ASAP, THANK YOU The four rigid gears, loaded as shown in the figure, are attached to a 2.89-in.-diameter steel shaft. Compute the angle of rotation of gear A relative to gear D if TA = 414 lbft, TB = 911 lbft, and TC = 1156 lbft. Use G = 12041783 psi for the shaft. Round off the final answer to four decimal places.
Correct and complete solution please
Torque in = 40nm Holding torque out = 896nm 8.Using your answers from the gear box above, and given that the input shaft has a diameter of 12 mm and the output shaft has a diameter of 15 mm, both shafts are made from aluminium. When this transmission system was operated, it failed. Identify the position where the failure occurred and the reason for this failure. Suggests improvements to the system to overcome the failure mode. The shear strength of aluminium is 207 MPa.
Show the derivation proccess of this formula from the precision cut gears with over 4000fpm.
The hollow shaft used in the system has the following conditions: Outer Ø:110 mmØ Allowable Shearing Stress:85 MPa Determine the thickness (mm) of the shaft. Round to the nearest whole number for the thickness and use 2 decimal places for other solved values. Provide a torque diagram, strictly follow instructed sign convention, and start from left to right.
The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20kW are used by gear A, 20 kW by gear C and 30kW by gear D. -20KW 7OKN -20kw -30kW 2m 1.5m 1.5m B (a) If a uniform shaft diameter of 125 mm B speci fied, detenmine the angle of rotation of A relative to D. O If segment Co is to be replaced ay a hollaw Shaft with an inside diameter of 80 mm, what is the outside diameter if the stress is not to excced 70 MPa.
PLEASE ANSWER PART 4 and 5 Part 1 Calculate the polar moments of inertia in segments (1) and (2). Answer: J₁ = 13.84 in.⁴ J₂= 1.535 in. ⁴ Part 2 Calculate the internal torques T1 and T2 in shaft segments (1) and (2), respectively. On paper, prepare an internal torque diagram for the compound shaft that shows these internal torques. Use the sign convention presented in Section 6-6. Answer: T₁ = 800 Ib-ft, T₂= -800 Ib-ft. Part 3 Calculate the maximum shear stress in each shaft segment. On paper, prepare a diagram that shows the maximum shear stress in segments (1) and (2) of the shaft. Use the sign convention presented in Section 6-6. Answer: τ₁ = 1560.69 psi, τ₂ = -7817.59 psi Part 4 (PLEASE ANSWER) Determine the rotation angle of B with respect to the support at A. Please Answer: φB= rad. Part 5 (PLEASE ANSWER) Determine the rotation angle of C with respect to the support at A. Please Answer: φC= rad.
PLEASE ANSWER ?? ?Part 1 Calculate the polar moments of inertia in segments (1) and (2). Please Answer: J₁ = in.⁴ J₂= in. ⁴ ?Part 2 Calculate the internal torques T1 and T2 in shaft segments (1) and (2), respectively. On paper, prepare an internal torque diagram for the compound shaft that shows these internal torques. Use the sign convention presented in Section 6-6. Please Answer: T₁ = Ib-ft, T₂= Ib-ft. ?Part 3 Calculate the maximum shear stress in each shaft segment. On paper, prepare a diagram that shows the maximum shear stress in segments (1) and (2) of the shaft. Use the sign convention presented in Section 6-6. Please Answer: τ₁ = psi, τ₂ = psi ?Part 4 Determine the rotation angle of B with respect to the support at A. Please Answer: φB= rad. ?Part 5 Determine the rotation angle of C with respect to the support at A. Please Answer: φC= rad. Thank you so much in advance