An 54 tooth spur gear transmits a torque of 15000N.mm. The pitch circle diameter is 150 mm, and the pressure angle is 20o. What is most likely the radial force on the gear?     73 N     42 N     31 N     64 N

Q: A 20 degree pressure angle spur gear set is transmitting 10 horsepower at 1,000 RPM. The pinion has…

A: The pressure angle = 20 degrees The horsepower, P = 10 hp the speed of the gear, N = 1000 rpm The…

Q: speed, Wh

A:

Q: in the an:iclo-kwise di

A:

Q: A 20 straight-tooth bevel pinion having 14 teeth and a diametral pitch of 4 teeth/in drives a…

A: Given Data: Number of teeth in Bevel pinion NP=14 Diametral pitch P=4 teeth/in Number of teeth in…

Q: Examine the gear drive shown.  The small driving gear has 15 teeth, DP = 8, RPM = 1200, Torque = 4…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: A gear box has an input speed of 2,000.00 rev/min clockwise and an output speed of 500.00 rev/min…

A: Given data, Nin = Input speed = 2000 rev/min Nout = Output speed = 500 rev/min Pin = Input power =…

Q: What is the transmitted load exerted by the pinion on the gear? Report your answer in lbf.

A: Given:Pinion Np=17 teeth, Gear Ng=52 teeth, Pressure angle∅=20∘ Power H=4 hp Diametral pitch Pd=10…

Q: In the coaxial gear train below, the speed of shaft Z is to be about but greater than 1/10th that of…

A:

Q: A pair of iron cast gears connecting two shafts at the Angle of the elbow. The diameter of the…

A: pitch diaDG=100mm=0.1mDP=80mm=0.08mϕ=14.5°σOP=55MPaσOG=55MPaP=2.75kWεP=εG=84kN/mm2

Q: A power of 25 KW is transmitted by a pair of spur gears. Pressure angle= 20, radial force generated…

A: Given, P = 25 kW, θ = 20 0, Fr = 220 daN = 2200 N, N = 600 N, t = 33, Dp2 / Dp1 = 3 We need to find…

Q: For the gear train below, the teeth numbers of the gears are N2= 47. N3-16, N4 = 30. N5-15. If the…

A: Given:The number of teeth on gear 2, The number of teeth on gear 3, The number of teeth on gear 4,…

Q: A 17-tooth 20° pressure angle spur gear rotates at 1800 rev/min and transmits 4 hp to a 52-tooth…

A:

Q: Two equal involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angle are in mesh.…

A: According to the given data Number of teeth (T)=40 Module (m)=3mm Pressure angle ϕ=20° Speed…

Q: 2. (03) The splined ends and gears attached to the A992 steel shaft are subjected to the torques…

A: Note:- here, part C). and D). has been asked so, I have answered that two parts here.here for steel…

Q: What is the total force exerted by the pinion on the gear? Report your answer in lbf.

A:

Q: Problem 2. A compound gear train as shown in the following figure, Gear 1 has 24 teeth and Gear…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.