For the gear train below, the teeth numbers of the gears are N2= 47. N3-16, N4 = 30. N5-15. If the input shaft (carrying gear 5) is rotating at 708 RPM, what is the speed of the output shaft (carrying gear 2)? $5

Q: The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A…

A:

Q: A gear train is made up of five spur gears as shown in the figure. Gear 2 is driver and gear 6 is…

A: Given data, Figure shown gear train is made of five spur gears. Where,  Gear 2 is driver and gear 6…

Q: n a compound train of gears spur gear 1, with 40 teeth and rotating at 15 rpm, drives a pinion 6…

A:

Q: In the figure below, Gears B and C represent a compound gear and have the following details. The…

A: number of teeth t A=100 tB=40 tc=80 tD=20 input torque  Ti=42 Nm speed of gear A NA=2400 rev/min…

Q: A 14.5° involute spur gear has a pitch diameter of 3 in. Determine the diameter of the base circle…

A: Given information, Pitch circle radius= 3/2 =1.5 inch, Find, Base circle diameter

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

A:

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

A:

Q: (Pinion) Gear 2 Idler N2 = 75 teeth Gear 3 Output N3 = 25 teeth O teeth he following: 1. Pinion…

A:

Q: Two mating spur gears have 40 and 120 teeth respectively. The pinion rotates at 1200 rpm and…

A: Given :- Two spur gear of Z1=40 teeth and Z2=120 teeth  Pinion rotates at N1=1200 rpm  Torque is…

Q: The shaft from a DC motor is connected to gear A which rotates at 45rps in clockwise direction.…

A:

Q: The gear train shown in the image has a pressure angle of 20° and a DP of 16. Shaft 2 is turning at…

A:

Q: A two-stage gear train consists of four gears meshed together (Figure 10). The secondand third gears…

A: for the given gear train  To determine  angular velocity of gear 4 in terms of ω1,n1,n2,n3 and n4

Q: e marimum velocity of slidi

A:

Q: Begin a full-size layout of a pair of spur gears having a 4:1 velocity ratio, a 10-in center…

A:

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

A:

Q: The double-reduction helical gearset shown in the figure is driven through shaft 'a' at a speed of…

A: The double-reduction helical gearset shown in the figure is driven through shaft 'a' at a speed of…

Q: Shaft a in the figure has a power input of 75 51T kW at a speed of 1000 rev/min in the…

A: Given data Input power = 75 kW Input Speed = 1000 rpm module = 5 mm Number of teeth on gear 1 = z1 =…

Q: The figure shows a rotating geared system. A torque of 3N is applied to an input gear in order to…

A: Given data: Input gear teeth = z = 11 Output gear teeth = Z = 99 Assuming that  Input gear torque =…

Q: The gear ratio shown must transmit 10 horsepower (66000 lb in/s) from its input, which is rotating…

A: For the solution refer below images.

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.