400 N-m 1200 N-m 600 N-m 600 mm 500 mm 200 N-m 400 mm

Q: The 54-mm diameter shaft is subjected to the torques as shown. Determine the angle of twist (in…

A:

Q: The shaft is made of A-36 steel, has a diameter of 95 mm, and is fixed at B while A is loose and can…

A: Write the given data.

Q: me 30-mm-diameter A-36 steel shaft bjected to the torques shown. Determin e angle of twist of the…

A: Solution is attached below

Q: The shaft is made of A992 steel. It has a diameter of 1 in. and is supported by bearings at A and D,…

A: Given Data: The diameter of the shaft is d = 1 in. The external torque acting at sections B and C…

Q: Q-1 The gears attached to the fixed -end steel shaft are subjected to the torques shown in fig .The…

A:

Q: A shaft with two segments (one with constant cross-section of 40-mm-diameter, 500-mm- length and one…

A: Given: T=13kND1=40mmD2=20mm Shear modulus of aluminium 6061-T6 (G)=26GPa

Q: The splined ends and gears attached to the A992 steel shaft are subjected to the torques. The shaft…

A: Diameter of the shaft (D)= 50 mmFor the A992 steel shaftthe value of the shear modulus is G=75Gpa

Q: The 60-mm-diameter shaft is made of 2014-T6 aluminum (G=27 GPa). If the allowable stress is Tallow =…

A:

Q: he 103-mm-diameter steel shaft is subjected to the torques shown. T1 = 12 kN-m, T2 = 2 kN-m, T3 = 5…

A:

Q: The gears attached to the A-36 steel shaft are subjected to the torques shown. Determine the angle…

A: Given data:Need to determine the angle of twist of end C with respect to the end A.

Q: The approximate distance between the two parallel shafts is 600 mm. The shafts are to be connected…

A: Given: N1=1000 rpmN2=2500 rpmm=12 mmc=600 mm

Q: If end B of the shaft, which has an equilateral triangular cross-section, is subjected to a torque…

A: Given data as per question Torque = 900 lb.ft Assuming G of the shaft = 3.7×103 ksi

Q: The motor delivers 65 hp to the A36 steel shaft while it rotates at 1500 RPM.  The shaft is…

A: Given, Total power being transmitted = P = 65 hp = 4.29 x 105 lbf-in/s Rotational speed of shaft = N…

Q: 1. The splined ends and gears attached to the A-36 steel shaft are subjected to the torques shown.…

A: Given data: d=40 mmShaft=A-36 steel Need to determine the angle of twist of end B with respect to…

Q: During the design of the shaft, it is recommended to assume that the radius of the shaft is not…

A: In mechanical enegineering,  Torsion is explained as the twisting of a shaft due to an applied…

Q: An aluminum shaft with a constant diameter of 50mm is loaded by torques applied to gears shown.…

A:

Q: The bwo 3-ftlong shafts are made of 2014-16 aluminum. Each has a diameter of 1.5 in and they are…

A:

Q: the solid steel sheft DF has a diameter of 25 mm and is supported by smooth bearings at D and E. It…

A: Please find the solution below.

Q: The 80mm diameter shaft is made of 6061-T6 aluminum allow and subjected to the torsional loading…

A:

Q: 21. The splined ends and gears attached to the A992 steel shaft arc subjected to the torques shown.…

A:

Q: The motor A delivers 7500 kW to the shaft at 3600 rev/min, of which 2500 kW is removed by gear B and…

A:

Q: The composite shaft consists of Aluminum (E= 70 GPa), Copper (E= 126 GPa) and Steel (E= 200 GPa).…

A:

Q: The approximate distance between the two parallel shafts is 600 mm. The shafts are to be connected…

A:

Q: The 45-mm-diameter A992 steel shaft is subjected to the torques shown where T = 760 N.m. - Part A…

A:

Q: A flange bolt coupling consists of 10-15mm diameter steel bolts on a bolt circle 300mm in diameter…

A:

Q: supplies a torque of The motor shown in Fig. 500 N· m to shaft BCDE. The torques removed at gears C,…

A: To find the torque transmitted by transverse cross-sections in BC,CD and DE of the shaft TBC=? TCD=?…

Q: The 80-mm-diameter shaft is made of steel. If it is subjected to the uniform distributed torque,…

A: Given Data: The length of the shaft is L = 800 mm. The uniformly distributed torque acting on the…

Q: q3..Shaft a transmits 7 hp. Determine the reaction a bearings A and C knowing that these bearings…

A:

Q: If the gears are subjected to the torques shown, determine the maximum shear stress in the segments…

A: Given Data: The diameter of the shaft is d= 40 mm. The torque at point A is TA = -300 N·m. The…

Q: The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. If the allowable shear stresses for…

A: Given Shear stress of magnesium = 45 MPa = 45 × 106 Pa Shear stress of steel = 75 MPa = 75 × 106 Pa…

Q: If the shaft has an equilateral triangle cross section and is made from an alloy that has allowable…

A: Given: τallow=12 ksia=3 inL=2 ft

Q: The shaft below is made of A992 steel and has an allowable shear stress of tadm = 75 MPa. When the…

A: Given: The allowable shear stress, τ = 75 MPa The speed of the shaft, N = 300 rpm The power of the…

Q: Please don't provide handwrittenh solution.

A: Tau=T/(D/2)(wL)T=2,300x1000/(50/2)(12.7x100)=…

Q: 4. The tapered shaft is made from E- 36 steel ( G = 80 GPa ), and has a radius which can be…

A: Given    Torque, T = 450 Nm    Length, L = 4 m Find     Angle of the twist

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.