H.W3 The simply supported beam diameter 50 mm shown in Fig. (a) supports 30-kN concentrated force at B and a 40-kN•m couple at D. A) Sketch the shear force and beading moment diagrams. B) Calculate the maximum bending stress and the maximum shear stress of the beam. Neglect the weight of the beam. Pn= 30 kN 4 m 3 m 3 m E A

H.W3 The simply supported beam diameter 50 mm shown in Fig. (a) supports 30-kN concentrated force at B and a 40-kN•m couple at D. A) Sketch the shear force and beading moment diagrams. B) Calculate the maximum bending stress and the maximum shear stress of the beam. Neglect the weight of the beam. Pn= 30 kN 4 m 3 m 3 m E A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Rank the absolute maximum shear stresses over the cross sections from the largest to the smallest.…

Q: eter of the pin at C in mm. c. Determine the corresponding bearing stress in the pedal at C in MPa.

A: Take moment about C∑ Mc=0TBA0.125-11000.3=0TBA=2640N∑ Fx=0TBA-Cx=0Cx=2640N∑ Fy=0 Cy=1100N…

Q: A nylon thread is to be subjected to tension of Q (N). The modulus of elasticity, E of the thread is…

Q: The beam is loaded by one couple at each of its ends, the beam cross-section shown below (Figure…

Q: Link AC has a uniform rectangular cross section 3 mm thick and 12 mm wide. Determine the normal…

A: Given: Link AC: thickness= 3mm, Width=12mm

Q: Problem II. The truss shown in the figure below is applied with force P (refer to the table of…

Q: A rectangular timber beam, 320 mm deep by 140 mm wide, is located as shown below: 140 2 kN 1 KN ↓↓ 3…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: If the beam is subjected to an internal moment of M = 30 kN-m determine the compressive bending…

Q: 100 mm Q.2) The right figure show the cantilever beam and loading, while the left figure show the…

A: Solution:- 1. Shear stress in the beam:

Q: 1) a. Determine the location of the plastic centroid for the column shown.

A: Given Data:fc=40Mpa.fy=420Mpa.

Q: shown, determine the factor of safety against yielding at the location of ELEMENT H using; a) t…

Q: 2. The simply supported wood beam ABC in Fig. (a) has the rectangular cross section shown. The beam…

Q: Q1). Determine the maximum stress produced by the loads and create the shear and moment diagram.

A: ∑MA = 0 = - By×10 + 200×4×2By = 160010 = 160 N∑FY = 0Ay + By = 200×4Ay = 800 -160 Ay = 640 N∑FX = 0…

Q: Week 5, Question 2: Using the force method, calculate the bending moment at B for the statically…

A: A frame is pinned at A and E, also a point load of 12kN is applied at B,To determine the moment at…

Q: Determine (a) the maximum bending stress, (b) th maximum shearing stress due to V in the simp…

A: GIVEN- A beam carrying UDL and concentrated moment of 16knm required- to find maximum bending stress…

Q: 4.1. The two-member pinned frame is subjected to the distributed loading shown. Member CB as a…

A: At a point in a section, stress is also known as force per unit area. Forces per unit area that act…

Q: Iso, determine the maximum fiber stress and the stress in a fiber 100mm from the top of the eam at…

A: Shear force and bending moment at the section is important for the structure to detemine the tensile…

Q: 1. For the W 21x 62 steel beam below determine the actual value of om in the beam and the maximum…

A: A simply supported beam at B and C, of length 30ft between B and C, with overhanging portion AB and…

Q: The T section shown in Fig. is the cross-section of a beam formed by joining two rectangular pieces…

A: Given : Max. shearing force in beam = 60kN This is a problem of solid mechanics where we are asked…

Q: The internal shear force V at a certain section of an aluminum beam is 40 kN. The beam's centroid is…

A: V = 40 kN, Location of Centroid from bottom = 54.4 mm, Moment of Inertia, Iz = 398300 mm4

Q: Q.3) A simply supported wide-flange (see figure below) beam of span length L carries a vertical…

A: Given : Section : W 10 X 30 L = 8.5 ft P = 5 kips Alpha = 26.57 degrees We are asked to determine…

Q: The beam shown in figure is made of wood and is subjected to resultant internal vertical shear force…

A: The shear force V=3 kip is acting downwards on the beam. NA is the neutral axis. Size of beam is 5"…

Q: 2 kN/m 10 kN 5 kN 1 kN/m B 2 m 2 m 3.

Concept explainers

Beams and Frames

A beam is a horizontal structure or a member which is always subjected to transverse shear loads.

Question

Asiacell
Asiacell
2_52830267386...
->
H.W3
The simply supported beam diameter 50 mm shown in Fig. (a) supports
30-kN concentrated force at B and a 40-kN•m couple at D. A) Sketch the
shear force and beading moment diagrams. B) Calculate the maximum
bending stress and the maximum shear stress of the beam. Neglect the
weight of the beam.
Pn= 30 kN
3 m
4 m
3 m
E
B
Cp= 40 KN•M
(a)
2
...

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

solve the problem
The frame supports the triangular distributed load shown. Determine the normal and shear stresses at point D that act perpendicular and parallel, respectively, to the grains. The grains at this point make an angle of 35° with the horizontal as shown.
1. A Using E = 100 GPA. IN.A. = 1,500 x 10 mm², compute the SUPPORT REACTIONS of the loaded beam shown when: a. supports are unyielding. b. support at the midspan yields 4 mm. 4m 60 KN/m B 2m www 10 KN C D 2m
3 of 5 QUESTION 4 For the beam and loading shown, draw the shear force and bending moment Diagram and determine the maximum normal stress due to bending on a transverse section at C. بست 10 kN 1.5m C 1.5m 3 kN/m 100 mm → 2.2 m Figure AQ4 200 mm
6
Q.2/The rigid beam shown in Figure 2 is supported by a pin at A and wires BD and CE. If the load P on the beam causes the end C to be displaced 10 mm downward, determine the normal strain developed in wires CE and BD. D 4 m P 2 2 m Figure 2 Rigid beam with wires and load
Answer proplem 1,3 and 1.4
The horizontal beam is supported by a pin at A and the pin-connected link BC. It has a uniformly distributed loading w = 2.6 kN/m as shown in the figure. All the pins are in double shear and have a diameter of 20 mm. Determine the max shear stress in the pin at C. Input your answer as a value only in MPa to one decimal place without +/- sign. W 1.5 m 2 m B 1m