1.AUsing E = 100 GPA. IN.A. = 1,500 x 10 mm², compute the SUPPORT REACTIONS of the loaded beam shown when:a. supports are unyielding.b. support at the midspan yields 4 mm.4m60 KN/mB2mwww10 KNCD2m

Answered: 1. A Using E = 100 GPA. IN.A. = 1,500 x…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

As shown in the figure, aluminum, E= 70GPa links (1) and (2) support rigid beam ABC. Link (1) has a cross-sectional area of 320mm² and link (2) has a cross-sectional area of 480mm². For an applied load of P= 58kN, determine the rigid beam deflection at point B. (2) 4,000 mm (1) 2,500 mm B 1,400 mm 800 mm
A square plate 2 m on each side is supported by four steel tie rods 6-mm-diameter from an overhead central point as shown in the figure STRM10. The plate supports a surface load of W in kPa. The point of attachment A is 1.25 m above the plane of the plate. 1.25 m 2 m 2 m
2. *The frame shown is pinned at the supports. The relative plastic moments are given. If M has the value of 108 kNm, calculate the value of W that will just cause the frame to collapse. W W 2W 2Mp D E 3m 6 m A B 2Mp 3m с 3 m Mp F
The beam ABC is subjected to a point load at the middle of segment AB and a uniformly distributed load at the segment BC, as shown in the figure. A 20 N Set Wo B 1.5W, N/m Figure 1: Overhang beam Find the equation of the elastic curve for the segment AB. L C - 3 N/m, L = 2 m, EI = 25000 Nm². Use the method of superposition for all parts. Hint: for x > L/2 in segment AB, the solution can be obtained from the table by replacing x by L-x.
Determine the maximum bending moment magnitude for the beam shown below. Use a = 18 ft, b = 6 ft, and w = 6 kips/ft. The reaction forces for this beam are Ay = 48 kips and By = 96 kips. %3D W В a b olerance is + 1 in the 3rd icant digit. Mmax ! kip-ft
In the figure, aluminum [E = 69 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a cross-sectional area of 290 mm² and link (2) has a cross-sectional area of 500 mm². For an applied load of P = 51 kN, determine the rigid beam deflection vg at point B. Assume a = 1630 mm, b = 890 mm, L₁= 2750 mm, and L₂=5120 mm. L₁ (1) a B P b (2) L2
B4
Using the virtual work method, detemine the vertical displacement of joint Cof the steel truss shown in Figure Q3. Assume E= 200 GPa and A = 500 mm for all members. 4 m 300 kN Im 120 kN 4m 4m Figure Q3
sl
4. A planar truss that is supported by a rolling pin support at point I and a fixed pin support at point A is shown in the accompanying figure. Two point loads are applied on the truss at points D and F, as indicated in the figure. Assume that all members of the truss are massless. n₂ 400m 40 FARN an AKN m 300 300 (a) Draw a free body diagram of the entire truss. (b) Using equilibrium conditions, calculate the reaction forces at points A and I. (c) Draw a free body diagram of point H; calculate the axial forces acting on member HH. (d) Determine the axial forces in members DF, DG, and EG.
A cantilever beam is 4m long with a EI = 20MNm^2. It has a point load of P=1kN at the free end and a u.d.l of q = 300N/m along its entire length. what is the reaction at A? what is the moment at A? Calculate the following at the free end slope and deflection
9 Consider the plane truss with load Pas shown in the figure. Let the horizontal and vertical reactions at the joint B be Hg and V, respectively and Vc be vertical reaction at the joint C. 2 exhoM S SLO 60° - II B A 60° D L 60° F 60° KLA G P с Which one of the following sets gives the correct values of VB, HB and V? (a) VB = 0; HB = 0; Vc = P (b) VB P/2; HB = 0; Vc = P/2 (c) VB = P/2; HB = P (sin60°); Vc = P/2 (d) VB = P; HB = P (cos(60°); Vc = 0 [2016

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

1. A Using E = 100 GPA. IN.A. = 1,500 x 10 mm², compute the SUPPORT REACTIONS of the loaded beam shown when: a. supports are unyielding. b. support at the midspan yields 4 mm. 4m 60 KN/m B 2m www 10 KN C D 2m