2. The simply supported wood beam ABC in Fig. (a) has the rectangular cross section shown. The beam supports a concentrated load of 300 N located 2 m from the left support. Determine the maximum displacement and maximum slope angle of the beam at 1.7 m from A. Use E = 12 GPa for the modulus of elasticity. Neglect the weight of the beam. 300 N B C A 80 mm 40 mm 1.0 m- Rc 2 m RA (а)

2. The simply supported wood beam ABC in Fig. (a) has the rectangular cross section shown. The beam supports a concentrated load of 300 N located 2 m from the left support. Determine the maximum displacement and maximum slope angle of the beam at 1.7 m from A. Use E = 12 GPa for the modulus of elasticity. Neglect the weight of the beam. 300 N B C A 80 mm 40 mm 1.0 m- Rc 2 m RA (а)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A proper cantilever ABCD is loaded as shown in figure. If it is of uniform cross-section, the collapse load of the beam will be nearly W/8 W Hagal B Mp Mp L/2 L/2 L/3 →→ D
W A L Test beam Strain gauge (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. Section A-A Strain gauge 1 b Strain gauge 3 Strain gauge 2 B (b) Location of Huggenberger strain gauges a Referring to the above figure, calculate the location of the centroid, the second moments and product of area for the cross-section if; • D = 67 mm B = 41 mm t = 2.41 mm. From these, calculate the position and orientation of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis). Also calculate the directions of the principal second moments of area. Next, graph as scale diagram of the cross-section and plot the neutral axis on that diagram in the correct location and indicate the direction of deflection for the same conditions
solve correctly and show the complete solution.
a) Determine the force P (in kN) required to stretch the Aluminum bar by 3mm. B) Determine the final width and thickness of the Aluminum bar. (1)
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
Rigid bar ABCD is loaded and supported as shown. Steel [E = 29900 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.81 in.2 and bar (2) has a cross-sectional area of 0.46 in.2. After load P is applied, the strain in bar (1) is found to be 770 με. Assume L1=55 in., L2=78 in., a=31 in., b=31 in., and c=36 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vD of point D on the rigid bar. (c) the load P.
A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as shown. Neglect deflections of the bar due to bending. Use E-200 GPa. How much will rod CD elongate due to the load at B?
The rigid beam shown has a cross sectional area of DB = 800 mm and defleetion at C- 20 mm due to the load P. Determine the normal strain in DB? 1250 Ridlen 100
Computation must be completeAnswer in two decimal placesBox your final answer
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F1 = 16 kips, F2 = 30 kips, and the normal stress in each rod must be limited to 18 ksi, determine the minimum diameter d1 required for rod (1).
А P 200 mm В E 150 mm F Three steel (E=200 GPa) rods (AB, CD and EF) support a load of P=30 kN as shown in the figure. Each of the rods AB and CD has a 80-mm2 cross-sectional area and rod EF has a 120-mm2 cross-sectional area. (a) Write the equilibrium equation for the rigid member BED in vertical direction, (b) write the compatibility equation for the given bar system, (c) determine the force in rod EF (d) determine the average normal stress in rod EF.