h PROBLEM 8.3-4

Q: A cylinder filled with oil is under pressurefrom a piston, as shown in the figure. The diameter dof…

A: Given   Shear stress = 5500 psi          Load, F = 3500 lb   Diameter, d = 1.80 in Find   Thickness,…

Q: The polymer bar shown in the figure below has a width of b = 58 mm, a depth of d = 92 mm, and a…

A: Width of  b = 58 mmDepth of d = 92 mmHeight of h = 282 mmCompressive load of P = 120kNThe bar height…

Q: The hollow drill pipe for an oil well (see figure)is 6.2 in. in outer diameter and 0.75 in. in…

A: Given Outer diameter = 6.2 in Thickness = 0.75 in Weight = 62 kips Torque = 185 kip-in To find…

Q: A trimetallic bar is uniformly compressedby an axial force P = 9 kips applied through a rigidend…

A:

Q: A cylindrical tank containing thickness Q2) compressed air has wall t 12mm and inside radius r=…

A: The stress that tends to burst a cylindrical pressure vessel circumferentially is termed…

Q: A circular plate with simply suppo KPa, as shown below, is considered. The plate thickness is h=23…

A: Pressure = P = 10 kPaPlate thickness  h = 23mmRadius of plate = 1.180 mmYoung's Modulus = 70 GPa =…

Q: 4 - A rectangular block is loaded with a 180 kN axial force and a moment M, as shown in the figure.…

A: Given data:-  Axial force =180 kN the maximum allowable tensile stress = 50 MPa To find:- the…

Q: 1. An underwater vehicle that can be approximated as a sphere of radius r = 0.8 m is to operate at…

A: Dear Students

Q: Problem 3 F-10,000N- L=1m Consider a tapered bar of circular cross-section shown in the Figure. The…

A: Given: The force, F =10,000 N The equation of radius, r = 0.06-0.03x The bar length, L = 1 m The…

Q: A sign ABCD is constructed from 7 mm thick plate steel (density p=8000 kg/m³) with the geometry…

A: To find:Determine the reaction forces at A and E. Given data:A sign ABCD is constructed from a steel…

Q: A high-strength steel bar used in a large cranehas a diameter d = 2.00 in. (see figure). The steel…

A:

Q: A cylindrical tank subjected to internal pressure p is simultaneously compressed by an axial force F…

A:

Q: Home Work 2 The articular Cartilage is subjected to plane stress ith normal stresses ox, Oy and…

A: Write the expression of the normal stress developed on an oblique surface when θ = 30°.

Q: A plane frame with pin supports at A and Ehas a cable attached at C, which runs over a…

A: a.Free body diagram:   No horizontal force on frame,henceEx=0Now,Ey+Ay=500lb⇒Ey=500lb-AyNow,Net…

Q: A pressurized cylindrical tank with flat ends is loaded by torques T and tensile forces P (see…

A: a) Maximum Permissible Value of Force P Given: p = 7.25 MPar = 125 mm = 0.125 mt = 6.5 mm = 0.0065 m…

Q: Problem 1: A gate AB as shown in the figure is 6 ft wide, hinged at point A, and restrained by a…

A:

Q: A roadway sign weighs 5.3 kN and is supported by a structural pipe that has an outside diameter of…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.