Answered: Problem 1: A gate AB as shown in the…

Problem 1: A gate AB as shown in the figure is 6 ft wide, hinged at point A, and restrained by a stop at point B. What is the force on the stop? 10' F 8' CG Gate 6² A B 6' 4'

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Choose forming and generating operation 2 points Work Work Thre dsad dsa Generated surface Work Work O dasd dsaa
Briefly disscus centrifugal seperation in hydro metallurgy
3. what are individual efficiencies that affect operation ?
Q6
where did you get value of Ws, the 572.116, the 0.9608, and 0.3350? you just copied the entire solution from internet
There may or may not be one or more mistakes in the solution. Go through the solution carefully and then do the following. 1. State if the solution is correct or incorrect 2. If the solution is incorrect, identify what is the mistake in the solution. Be specific and succinct. 3. If the solution is incorrect, provide the final solution with appropriate steps. Problem: A refrigeration cycle uses refrigerant R-134a to cool down water from 40°C to 20°C. The refrigerant R-134a enters the cycle as saturated liquid at -15°C and exits as saturated vapor at the same temperature. The mass flow rate of R-134a is 0.12 kg/s. The overall heat transfer coefficient is 1400 W/m².K. The surface area of the heat exchanger is 1.4 m². What is the rate at which heat is being exchanged between R-134a and water? Assume that the heat exchanger is perfectly insulated from outside (i.e., there is no convection or radiation with the outside/surrounding). Solution: We know, from the definition of overall heat…
Solution 1: Ergonomic Assessment and Improvement. An ergonomic assessment of Paula's workstation could identify areas where adjustments could be made to reduce strain on her wrists. This could include adjusting the height of the workstation, providing wrist supports, or changing the design of the tools she uses. The strength of this solution is that it directly addresses the physical strain causing Paula's discomfort. However, the weakness is that it may require investment in new equipment or tools, and the effectiveness will depend on the specific changes made. Solution 2: Job Rotation. Paula could be rotated between different tasks more frequently, reducing the amount of time she spends on tasks that strain her wrists. This could also include training other workers to perform the welding and gaging operations, allowing for more flexibility in task assignments. The strength of this solution is that it reduces the repetitive strain on Paula's wrists. The weakness is that it requires…
Describe the following: a) Internal sensible heat load with exampleb) Internal latent heat load with examplec) Combined Internal sensible and latent heat load with example
(c) Explain critical point and triple point with suitable example.
Through the following formulas: (100-FGM) DP 100-IGM WGI= where: WGI - Wet grain input in ton/h DP-Dryer performance in ton/h FGM - Final grain moisture in % IGM - Initial grain moisture in % EP =WGI-DP where: EP - Evaporation power in ton+₂0/h EC = GC HP where: EC - Energy consumption in kcal/h GC-gasoil consumption in kg/h HP-heating power of gasoil in kcal/kg SEC where: SEC - Specific energy consumption in kcal/kgH20 Select which of the following specific energy consumption options correspond to a dryer that has a performance of 40 tons/h, and is required to reduce grain moisture from 17% to 13.5%. Data: EC EP-1000 heating power of gasoil-10100 kcal/kg gasoil consumption=213 kg/h Answer 500-1000 kcal/kg H20 1500-2000 kcal/kg H20 1000-1500 kcal/kg H20 O O O
i need the answer quickly