Answered: Given is the 200mm X 400 mm rectangular…

Given is the 200mm X 400 mm rectangular beam below. 9 kN 7.50 kN/m 400 mm 1.50 kNm A 1.50m 7.50m 200 mm R1 R2 Figure 1 What is the section modulus of the beam in mm3 ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A beam is loaded as shown in the figure. What is the location of the concentrated load from point B?

A: Find resultant:∑ Fy=0 R-2036-1250-2036=0 R=1260lb

Q: Situation 1: A W8x67 has a length of 7.50 m. Fy= 248 MPa. The properties are given below. Properties…

A: Slenderness ratio = kl/rmin Slenderness ratio= (1/√2)*7500/53.80 Slenderness ratio=98.57 Allowable…

Q: Given is the 200mm X 400 mm rectangular beam below. 9 kN 7.50 kN/m 400 mm 1.50 kNm A 7.50m 200 mm…

A: The dimensions of the beam are 200mm × 400mm. => B = 200 mm & D = 400 mm. Thr cross-sectional…

Q: For the W18 X 55 beam, made of A992 structural steel, what is the slope at C and the deflection at…

Q: Q3/ For the figure shown below, compute the centroid of the figure. 4-5 m

Q: Given the following structure that is made of Aluminum, subjected to a tensile load equal to 56 kN.…

A: (a) The formula to calculate the strain is given by, ε=Change in lengthOriginal length=∆lL…

Q: A piece of wood was cut into 3 pieces as shown below and will form into a l-beam section. Planks 1…

Q: Determine the axial force (kN) in each member of the assembly shown below. Cross-Sectional Modulus…

Q: Answer in whole number w C A x В L- L/2

Q: A free The (M/EI) diagram of a cantilever beam is shown in the Figure. If the deflection of the free…

Q: Complete Table P4.2. For a member where a deflection criterion controls,which material would require…

A: As section 7178 T76 Aluminum is given. Using AISI Code steel table :

Q: The beam is loaded as shown. which of the following nearly givės the flexural stress due to…

Q: Determine the axial force (kN) in each member of the assembly shown below. Member Cross-Sectional…

Q: A T-shaped built up steel beam is composed of 150 mm x 11 mm flange plate at top and a vertical web…

Q: For the overhanging beam shown, calculate the deflection of the elastic curve midway between the su…

Q: For the given W8x35 I-Beam and the loading condition shown in the image, determine the maximum shear…

A: Solution: Find the support reactions: Taking moment about A: ΣMA=0RD×12=2×6×3+6×14RD=10 kips Taking…

Q: 4- Determine the maximum compression and tensile stress due to bending on the cross section shown…

A: Given that:

Q: A cantilever beam of 7.2 m span is a part of a floor supporting a concrete hollow block partition.…

A: Deflection : The degree to which a component of a structural member is shifted under a load is known…

Q: As depicted in the diagram, a beam is loaded. Where does the concentrated load originate from point…

Q: a. Name at least one example where this type of bending is desirable and where it is undesirable.…

A: Given, Plot Length vs deflection data : To find : Example where this type of bending is desirable…

Q: The beam is loaded as shown. which of the following nearly gives the flexural stress du to tension…

A: Find the reactions :RA=RB=12×4+2×12×12×42=48kNMax moment will be at the midspan…

Q: lexalexatagal 24 m 24 m 16 mm A beam of the cross section shown is extruded from an aluminum alloy…

A: Given data We are given that Yield stress σγ = 250 Mpa Ultimate stress σu = 450 Mpa Factor of…

Q: The beam ABC shown in given figure is horizontal. The distance to the point of contraflexure from…

A: Given data, The distance to the point of contra flexure from the fixed end A

Q: 3. A homogeneous beam with an overall weight of W is to be connected, as shown below, to 2 cables…

Q: Below is a trapezoidal beam with 3-28mm reinforcing bars at the bottom. Using the design properties…

Q: The second moment of area about the centroidal x-axis (lxxcentroid) for the solid homogeneous beam…

A: Second moment of area about x axis (Ixx) = 201288.96 mm4 .

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1530…

Q: 350 mm fe = 21 MPa fy = 414 MPa Ø = 0.75 Stirrups – 10mm Ø 600 mm

A: All beams have stirrups spaced at d/2 or less throughout their length and at 8 db, or less at…

Q: Compute the area of steel for the L-section shown in the figure if it is subjected to M₁ = 120 kN.m…

A: Width of flange is bf=600 mm.Width of web is bw=120 mm.Effective depth is d=400 mm.Depth of flange…

Q: A beam is simply supported and has a span of 12 m. The beam is a W33x240 with Ex-345 MPa. Compute…

A: Answer Since we are not given any data related to lateral bracing let us consider that bracings are…

Q: Given beam and load as shown, Oallow=18 MPa and Tallow =2.57 MPa. Determine the dimensions of the…

Q: A cross-sectional area of 322.58 mm of an aluminum bar which carries the axial loads applied at the…

A: Find the total change in length of the bar

Q: 2KN/m El = 1600Nm² %3D 6m 4m Figure 06

A: Free body diagram and reactions - Force in the vertical direction - RA +RB = 2×4RA + RB = 8 KN…

Q: A simple beam of steel structure with a concentrated load in the middle of the span is known as…

A: A simple beam of steel structure with a concentrated load in the middle of the span E = 200000 MPa…

Q: Question: A rectangular column is shown in the figure, assuming fc'=28Mpa, fy=345Mpa, and e=155mm,…

A: Given that :-A rectangular column is shown in the figure, assuming fc'=28Mpa,fy= 345Mpa,and e= 155…

Q: From the figure shown, determine the following: a. The plastic moment of the whole beam. The order…

A: Solution: Find the actual plastic moment: The mechanism for span AB: The maximum moment will occur…

Q: For deflection y units in a beam which of the following relation holds good? OⓇ = dy/dx de/dx =…

A: deflection in beam is equal to y Questions is from structural analysis here the defection in beam is…

Q: Using fy = 420 MPa and fc' = 28 MPa, determine the design moment of the beam cross-section shown.…

A: Given a inverted T beam Calculate design moment ( sagging)

Q: Q7/ A simply supported beam of cross section shown in figure supports a uniform load over a span of…

Q: Given is the 200mm X 400 mm rectangular beam below. 9 kN 7.50 kN/m 400 mm 1.50 kNm A 1.50m 7.50m 200…

A: We will use formula for Moment of Inertia.

Concept explainers

State Plane Coordinate Systems

The state plane coordinate system (SPCS or SPS) is a collection of 124 coordinate systems or geographic zones prepared for particular regions of the U.S. Every state consists of one or more than one state plane zone, the boundaries of which generally follow the county lines. Inside the U.S., there are 110 zones in total, 10 more zones in Alaska, 5 in Hawaii, and 1 for Puerto Rico and US Virgin islands. The system is extensively used for geospatial and geographic data assembling by the state and local governments.

Question

Given is the 200mm X 400 mm rectangular beam below.
9 kN
7.50 kN/m
400 mm
1.50 kNm
A
1.50m
7.50m
200 mm
R1
R2
Figure 1
What is the section modulus of the beam in mm3 ?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

What formula is used? (Boxed formulas) and why is Es = 200,000? thanks.
Question 1. Is Beam b2, b2a,b2b support on b11 b11a and b12 b12a? or beam b11,b11a,b12,b12a support on beam b2,b2a,b2b? 2. Identify the multi-span beam and single span beam.
The following are the properties of a steel section to be used for a beam section:Fy = 248 MPa Area = 21300Ix = 300000000 Iy = 98800000Sx = 2080000 Sy = 746000d = 289 tw = 19.2tf= 31.8 bf = 265w beam in kN/m = 9laterally unsupported length, Lb = 3 m 1. What is the minimum unsupported length of the beam to be considered long? a. 16.2 m b. 14.5 m c. 13.6 m d. 12.8 m 2. What is the critical depth over thickness ratio set by NSCP? a. 206.68 b. 126.68 c. 106.68 d. 16.68 3. What is the allowable bending stress in the given beam section? a. 148.8 b. 163.68 c. 142.68 d. 124.68 4. If the laterally unsupported length been 10 m, what is the allowable bending stress as per NSCP 2001? a. 148.8 b. 163.68 c. 142.68 d. 124.68
"QC.25. Figure below shows a nonsway frame. The following are the properties of the beams and columns: For beams AD and AE cross section is 330 by mm 500 mm. For beams BF and BG cross section is 330 by 570 mm and columns AB to AC is 330 by 530 mm. Also, the lengths in meters are L1 = 5.3, L2 = 5.6, L3 = 6.1, and L4 = 7.2 meters. The column AB is bent in single curvature about its y- axis. It is carrying a total factored axial load of 560 kN with an unfactored dead axial load of 196 kN. The factored end moments are 111 and 119 kN-m. If f'c = 27.1 MPa and fy = 414.8 MPa (1) What is the effective length factor of column AB, (2) What is the critical load of the column AB?, (3) Determine its moment magnifying factor, and (4) Determine the actual eccentricity of the load. "
Q1: Compute the value of EIS at the distance 3m from A for the beam shown below: 1 kN/m M-2 kN-m 3 m 1 m. 1 m R1 R2
A mild steel bar 60mm in diameter is simply supported and has a span of 2m. What load suspended at the middle of the span will cause a deflection of 8mm? E = 200000MPA, specific weight if steel is 75KN/cu.m. 5.08 KN 5.84 KN 8.50 KN 4.85 KN
1. The I-section shown below Is to be used as part of a roof truss. Compute for the centroid and the moment of Inertia 20 mm 140 mm 100 mm 20 mm 100 mm 20 mm
A T-shaped built up steel beam is composed of 150 mm x 11 mm flange plate at top and a vertical web plate 210 mm x 17 mm. All plates used are A36 steel. Calculate the plastic section modulus about the horizontal x-axis in x103 mm3 with 2 decimal places.
please show all your solutions I NEED IT ASAP PLEASE
Below is a trapezoidal beam with 3-28mm reinforcing bars at the bottom. Using the design properties of fc' = 21MPa, fs = 140MPa, n = 7, 50mm effective cover, determine the following: Note: Assume the beam has cracked. 650 50 150 500 200 150 What is the Moment of Inertia of the Transformed section of the beam? Express your answer in mm4.
For the beam structure shown below the data is as follows: P= 9.6-kN, L = 6-m, d= 2.4-m, b=100-mm, t-30-mm h=150-mm and h₁-130-mm. Neglect the self-weight of the beam. Based on this information answer the following question: Question 2.2: What is the moment of inertia of the cross-section? [Enter value in mm as appropriate] L B hy
Determine the axial force (kN) in each member of the assembly shown below. Member Cross-Sectional Area Modulus of Elasticity AB 1,400 mm2 200 GPa BC 1,800 mm2 200 GPa DB 1,400 mm? 200 GPa C BY 18KN 400mm 400mm 400mm 55.00° 55.00°