Q7/ A simply supported beam of cross section shown in figure supports a uniform load over a span of 5 m. Use the data below to find: A. Allowable live load can be carried by this beam. B. If the uniform live load = 50kN/m, can the beam carry the applied 2016mm load? 4020mm Data: f = 28MPa, fy = 350 MPa , y = 24, D. L = self weight Ans. L.L=36.6kN/m 300 009

Q7/ A simply supported beam of cross section shown in figure supports a uniform load over a span of 5 m. Use the data below to find: A. Allowable live load can be carried by this beam. B. If the uniform live load = 50kN/m, can the beam carry the applied 2016mm load? 4020mm Data: f = 28MPa, fy = 350 MPa , y = 24, D. L = self weight Ans. L.L=36.6kN/m 300 009

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3) The simply supported beam with the cross-section as shown supports a total uniformly distributed load of 4P and 2P and concentrated load P as shown in the figure. Determine the maximum allowable value of P if the allowable flexural stresses are limited to 35 MPa in tension and 150 MPa in compression respectively. 1m P B 1m IC 4P 3m D 2P 1m DE U 175 200 (Dimensions in mm)
Determine the design strength of a T-Beam with the following data: b+= 700 mm bw = 300 mm hy = 100 mm d = 500 mm f₂ = 21 MPa fy = 414 MPa A: 5-20 mm dia.
9. A steel portal frame has dimensions, plastic moment capacities and applied loads as shown in the figure. The vertical load is always twice of the horizontal load. The collapse load P required for the development of a beam mechanism is P A B Mp K 2P 2Mp L с Mp D L
Current Attempt in Progress The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; = 1990 in."). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA= 250 kip-ft, P= 14 kips, LAB = 4.1 ft, LBc = 6.2 ft. MA LAB LBC Answer: in. (a) VA- in. (b) VB - 4. Submi Attempts: 0 of 1 used Save for Later
SHOW COMPLETE FBD
A lightly welded steel beam shown in Figure 5 is continuously supported along its length. A downward concentrated load of 4P acts at Point C, and two downward concentrated loads P act at Points A and E. The beam with full lateral restraint is bent about its major principal x-axis. Determine the followings: a. Section type based on section slenderness; b. Effective section modulus; c. The maximum design value of P. A k B fu 6 m d tw bf 6 m tf 4P d bf tw tf = - = fyf= fyw 6 m D um * 550 mm 206 mm 6 mm 10 mm 320 MPa = 340 MPa Zx=1362985 mm³ Sx 1533750 mm³ Figure 5 Steel beam under design loads. 6 m P E
Using plastic member capacity analyse the beam shown in figure Q6 to establish the minimum required plastic section capacity for the loading shown on the continuous beam.
Determine the design strength of a T- Beam given the following data: b = 700 mm by = 300 mm hf = 100 mm d = 500 mm fe' = 21 MPa fy = 414 MPa As: 5- 20 mm dia.