G- In a smooth inclined pipe of uniform diameter 250 mm, a pressure of 50 kPa was observed at section 1 which was at elevation 10 m. At another section 2 at elevation 15 m, the pressure was 20 kPa and the velocity was 1.25 m/s .The fluid in the pipe is water and the density of water at 20°C and 760 mm Hg is 998 kg/m3. Is the direction of flow is: * from section 1 to section 2 None of the above from section 2 to section 1

G- In a smooth inclined pipe of uniform diameter 250 mm, a pressure of 50 kPa was observed at section 1 which was at elevation 10 m. At another section 2 at elevation 15 m, the pressure was 20 kPa and the velocity was 1.25 m/s .The fluid in the pipe is water and the density of water at 20°C and 760 mm Hg is 998 kg/m3. Is the direction of flow is: * from section 1 to section 2 None of the above from section 2 to section 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As in the figure, a U-shaped pipe piece in the horizontal plane has water flow. At flange (1) total pressure pressure is 200 kPa, resulting in a mass flow of 40 kg/s to the pipe. At flange (2) , the total pressure is 150 kPa and the mass flow is 30 kg/s from the pipe. At (3) mass flow rate of 4 kg/sec from the section and 6 kg/sec from the (4) section to the atmosphere at 100 kPa pressure is discarded. With relative powers; Determine your Total Rx Ry forces at flange(1) and (2). ***Sections (1) and (2) are close enough ***density of water ??? = 1000 ??/?3 ***kinetic energy correction factor = 1,035 and momentum flow correction coefficient 1,025 *** mass flow = density*flow rate
Q=2000J Tout=? V(m/s) D=0.1m air Air at (2.95x10^2) K is entering in a circular pipe at 101325 Pa as shown in Figure. The velocity of the air at the pipe entrance is (1.5000x10^0) m/s. The diameter of the pipe is 0.1m. Specific gas constant of air is 287 J/kg-K. Specific heat of air is 100O J/kg-K. Find the outlet temperature if 2000 J of heat is added to the pipe. Answer should be in 'K' with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: Activate Windows Go to Settings to activat (? 9°C ENG 2020
The square-section duct in atmospheric conditions is exposed to outside air flow as seen in the figure. The temperature of the air is T air= 5°C, the velocity is V air= 10m/s. Find the exit temperature of the water entering the channel at a flow rate of ṁwater=0.01 kg/s and a temperature of T water,g=50°C. Geometric dimensions are given on the figure.
S CE - Oil is transported from A to B along a pipe of constant diameter. The pipe is inclined at 50° to the horizontal and B is at the higher elevation. Considering the flow from A to B, which statement is correct? O The pressure head is decreasing and the velocity head is increasing. O The pressure head is increasing and the velocity head is decreasing. O The pressure head and velocity head are both increasing. O The pressure head is decreasing and the velocity head is constant. O The pressure head and velocity head are both decreasing. P Type here to search 0022 10°C Sunny AG A Q0 ENG 16/02/2022 DELL Esc F6 FB num 2 4€ E R Y F G J K ck D %23 B N M end V page page up ctri alt gr alt
A 30mm ID, 50mm OD aluminum round tube passes air through it at a rate of 0.08 m^3/s. A 100W electric heater blanket covers the outside of the 2m long tube. If the air enters the tube at 100 celsius , what temperature does it exit at? Assume that the heater blanket is perfectly insulated on the back side (no heat loss out the back). Note-RT is 25 celsius
PLease refer to image tq
Air flows from a 10cm pipe in which the temperature and pressure are 4-C and 280kpa, respectively, into a 5cm pipe in which the pressure is 147kpa gage. Calculate the velocity and discharge in each pipe, assuming isothermal conditions, standard atmospheric pressure and no losses. The gas constant for air is 280N-m/kg-K.
What’s the answer for this please ?
Water vapor enters a Lule with an input cross-sectional area of 0.02 m2 at a temperature of 1.8 MPa and 400C. Water vapor passes through the Lule with a flow of 5 kg/s, and in this process there is a heat loss of 2.8 kJ / kg from the Lule. If the pressure at the outlet is 1.4 MPa and the speed is 275 M/s, find the speed at which the water vapor enters the Lule and the temperature at the outlet of the Lule.
Q=2000J Tout=? V(m/s) D=0.1m air Air at (3.050x10^2) K is entering in a circular pipe at 101325 Pa as shown in Figure. The velocity of the air at the pipe entrance is (1.50x10^0) m/s. The diameter of the pipe is 0.1m. Specific gas constant of air is 287 J/kg-K. Specific heat of air is 1000 J/kg-K. Find the outlet temperature if 2000 J of heat is added to the pipe. Answer should be in 'K' with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: x10 Answer DELL
(1) Given the working form of the Bernoulli equation as V2 + gz + dW --F dm Where 3 is the friction heating per unit mass dQ F = Au – dm Given also that friction heating in laminar flow of Newtonian fluids in circular pipes is given as µ 128 = -gAz = Q Ax -ΔΡ F = Ax is change in the x-direction. A typical capillary viscometer has a large-diameter reservoir and a long, small diameter, vertical tube. The sample is placed in the reservoir and the flow rate due to gravity is measured. The tube is 0.1 m long and has a 1 mm ID. The height of the fluid in the reservoir above the inlet to the tube is 0.02 m. The fluid being tested has a density of 1050 kg / m³. The flow rate is 10* m³ / s. What is the viscosity of the fluid?
Water flows through a measuring nozzle of 40mm diameter in a pipe of 75mm in diameter at a flow rate of 0.015 m3/s. Determine the pressure difference through the nozzle if the temperature is (a) 10°C, (b) 80°C.