4. An experimental test rig is used to examine two-phase flow regimes in horizontal pipelines. A particular experiment involved uses air and water at a temperature of 25°C, which flow through a horizontal glass tube with an internal diameter of 25.4 mm and a length of 40 m. Water is admitted at a controlled rate of 0.026 kgs-¹ at one end and air at a rate of 5 × 104 kgs-¹ in the same direction. The density of water is 1000 kgm 3, and the density of air is 1.2 kgm ³. Determine the mass flow rate, the mean density, gas void fraction, and the superficial velocities of the air and water. Answer: 0.02605 kgs-¹, 61.1 kgm-³, 0.94, 0.822 ms ¹, 0.051 ms-¹

4. An experimental test rig is used to examine two-phase flow regimes in horizontal pipelines. A particular experiment involved uses air and water at a temperature of 25°C, which flow through a horizontal glass tube with an internal diameter of 25.4 mm and a length of 40 m. Water is admitted at a controlled rate of 0.026 kgs-¹ at one end and air at a rate of 5 × 104 kgs-¹ in the same direction. The density of water is 1000 kgm 3, and the density of air is 1.2 kgm ³. Determine the mass flow rate, the mean density, gas void fraction, and the superficial velocities of the air and water. Answer: 0.02605 kgs-¹, 61.1 kgm-³, 0.94, 0.822 ms ¹, 0.051 ms-¹

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: ers a 12-cm-diameter 20-m-long isothermal pipe= aFigure Q4. Take the pressure of air 1 atm,

Q: Water enters at section 1 at 10 m/s with sp gr of 0.998 and alcohol enters sections 2 at 6 m/s with…

Q: (b) Consider fully developed flow of an incompressible Newtonian liquid in an in- finitely long tube…

A: (b Given Data u(y,z)=0y2a2+z2b2=1 On neglecting gravity the consistent state navier stokes…

Q: Q=2000J Tout=? V(m/s) D=0.1m 1IIIII air Air at (3.20x10^2) K is entering in a circular pipe at…

Q: determine the flowrate through the hole. m3/s Would the ball become noticeably softer during a…

Q: 4- Consider the fully developed flow of glycerin at 40°C through a 70-m-long, 2-cm-diameter,…

A: Given data as per questionLength of pipe = 70 mDiameter = 4 cmVelocity of fluid = 6 m/sDensity of…

Q: Q6) The flow-metering device shown consists of a stagnation probe at station 2 and a static pressure…

Q: Water flows in a certain cylindrical pipe Im long with an inside diameter of 1mm. The pressure…

A: Given:Length of the pipe, L=1 mPipe diameter, d= 1mm=0.001 mPressure difference between the ends of…

Q: Air at (5.15x10^2) K flows out of a circular pipe at 101325 Pa as shown in Figure. The mass flowrate…

Q: 3. Sketch the shear stress and velocity distribution for laminar flow across a pipe section.

A: In pipe flow, flow can be treated as the laminar flow when the value of Reynolds number is less than…

Q: A Pitot-static probe is mounted in a 2.5-cm-inner diameter pipe at a location where the local…

A: Diameter of pipe is (d) = 2.5 cm = 2.5*0.01 (m)…

Q: nswwer with diagram and complete solution: Establish the shear stress profile, velocity profile,…

A: Given: for a non Newtonian incompressible fluid Length of pipe = L Diameter of pipe = D at the…

Q: Air is flowing in a duct as shown in the figure below. A Pitot-static tube and a thermocouple are…

A: Given ,

Q: A patient receives IV fluid through a needle of radius 0.200 mm and length 2.0 cm. The density of…

A: Given Data: Needle radius r = 0.2 mm =2*10-4 m Needle Length L = 2 cm = 0.02 m density of the IV…

Q: 5. Dry saturated steam at 1.25MPA flows along steam main of 150 mm internal diameter at 24m/s.…

A: Given Data V1=24 m/s P1=1.25 MPa, dry saturated D1=150 mm P2=0.12 MPa Ms=4.5 kg Mw=90 kg

Q: Given that h=30 mm, μ=0.002 Pa.s and ρ=1000 kgm-3 Consider a steady-state turbulent flow between…

A: 1 2

Q: Air at 15 °C is flowing in a 2.75-mm-diameter tube at such a rate that the wall shear stress has a…

A: Given data: d=2.75 mmτw=3.3×10-4 N/m2T=15°C Need to determine the mass flow rate of the air.

Q: A 0.30 m X 0.40 m branch duct leaves a 0.30 m X 0.60 m main duct at an angle of 60°. The air…

Q: Which statement best describes the pipe friction coefficient for a laminar fluid flow through a…

Q: The air is flowing in the circular pipe with a volumetric flow rate of 11 m/h and diameter of the…

A: "Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: An incompressible fluid of density ? and viscosity ? flows through a curved duct that turns the flow…

Q: Velocity Profiles for Flow Between Parallel Plates. In Example 8.3-2, a fluid is flowing between…

Q: Two incompressible fluids (m1=2m2) are flowing at the same mass flow rates in homogenous pipes with…

Q: Carbon dioxide is being pumped through a smooth pipe at the rate of 3×10-4 kmol/sec for a distance…

A: Given data: m=3×10-4 kmolsL=2000 mT=323.15 KPi=750 kPaPo=430 kPaμ=1.45×10-5 kgms

Q: A liquid while flowing through a thin-walled cylindrical copper pipe (D=10 cm, L=1 m) with a mass…

Question

4. An experimental test rig is used to examine two-phase flow regimes
in horizontal pipelines. A particular experiment involved uses air
and water at a temperature of 25°C, which flow through a horizontal
glass tube with an internal diameter of 25.4 mm and a length of 40 m.
Water is admitted at a controlled rate of 0.026 kgs¹ at one end and air
at a rate of 5 x 104 kgs-¹ in the same direction. The density of water
is 1000 kgm 3, and the density of air is 1.2 kgm 3. Determine the mass
flow rate, the mean density, gas void fraction, and the superficial
velocities of the air and water. Answer: 0.02605 kgs-¹, 61.1 kgm-³, 0.94,
0.822 ms-¹, 0.051 ms-¹

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

Step 2: solution

Step 3: solution

Solution

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

3. A natural gas is flowing through a long distance smooth pipeline (1 m in diameter) at a constant temperature. The gas enters the pipeline at a velocity of 12 m s-1 and at the temperature and pressure of 20 °C and 690 kPa, respectively. Compressors and coolers are provided every 15 km along the pipeline to recompress and cool the gas to its initial temperature and pressure. Calculate the theoretical power requirement to compress the gas by each compressor. Assume that the compression is an adiabatic frictionless process and the work done by the compressor on unit mass of gas is given by: AW = Pout vdP [J kg-¹] Pin where Pin and Pout are the pressures at the inlet and outlet of the compressor, respectively, and vis the specific volume of gas. Hint: see Coulson and Richardson, Volume 1, Section 8.3.4, page 347-351. Specific heat ratio y (= C₂/C₂) = 1.3 [Ans. 845631 W]
Show complete solution: Prove that for a fluid with a constant density ρ flowing at a steady-state through a straight pipe with an entry diameter of D1 and an exit diameter of D2 where D1 > D2, the difference of the velocities, i.e. v1 – v2 (velocity in – velocity out), has a negative value. Suppose that for the same system, the ratio of the velocities v1/v2 = 1/4, what is the relationship between D1 and D2?
A pipe takes water from a reservoir where the temperature is 12 °C to a hydro- electric plant 600 m below. At the 1.2 m diameter inlet to the powerhouse the gauge pressure of the water is 5.5 MPa and its mean velocity 2 m: s'. If its temperature there is 13.8 °C, at what rate has heat passed into the pipe as a result of hot sunshine? (Note: The change of atmospheric pressure over 600 m must be accounted for: mean atmospheric density = 1.225 kg m³. Specific heat capacity of water = 4.187 kJ · kg ·K-1.) S
Air is flowing in a duct as shown in the figure below. A Pitot-static tube and a thermocouple are inserted into the flow stream as shown. Calculate the air velocity and the air-mass flowrate. The area of the duct is 1 ft², and the temperature of the control volume x is 40°F. V = m = i x ft/s lbm/s A Ps = 3 psig Po = 15 psig
6-4 (1) Air flows through a Venturi channel of rectangular cross- section as shown. The constant width of the channel is 0.06 m, and the height at the exit is 0.04 m. Compressibility and viscous effects are negligible. (a) Determine the flow rate when water is drawn up 0.10 m in a small tube attached to the static pressure tap at the throat where the channel height is 0.02 m. (b) Determine the channel height, h2, at section (2) where, for the same flow rate as in part (a), the water is drawn up to 0.05 m. (c) Determine the pressure needed at section (1) to produce this flow. 0.04 m 0.10 m b = width = 0.06 m 10.02m Water (2) ₂ Air 0.05 m Q Free jet 0.04 m
Kerosene at T = 20°C flows through the 100-mm-diameter commercial steel pipe at 22.5 kg/s. Use the equation 1 1.8 log Figure [(P) 3.7 60% 4 6.9 Re (Figure 1) 1 of 1 Determine the pressure drop that occurs over the 40-m length. Express your answer to three significant figures and include the appropriate units. PA PB = 384 kPa You have already submitted this answer. Enter a new answer. No credit lost. Try again. Submit E Previous Answers Request Answer ? Review
Prove that the speed of an incompressible fluid through a constriction, such as in a Venturi tube, increases by a factor equal to the square of the factor by which the diameter decreases. (The converse applies for flow out of a constriction into a larger-diameter region.)
The present pumping rate of crude oil through the Alaska Pipeline with an ID of 39 in is 550,000 barrels per day (1 barrel is 42 U. S. gallons). For crude oil at 60ºC, take ρ = 860 kg/m3 and μ ≈ 0.004 kg/m·s. What would be the maximum rate if the flow were constrained to be laminar? Take π = 22/7. Answer is asking for maximum flow rate for barrels per day
H.W. (a) Derive an expression for the volumetric flow rate of a fluid flowing through an orificemeter. Write down the advantages and disadvantages of using orificemeter over a venturimeter. (b) Water is flowing through a pipeline of 50 cm ID at 30°C. An orifice is placed in the pipeline to measure the flow rate. Orifice diameter is 20 cm. If the manometer reads 30 cm of Hg, calculate the water flow rate and velocity of the fluid through the pipe. pwater at 30°C = 987 kg/m³. p = 13600 kg/m. Orifice co-efficient. = 0.6 3/5/2024 61 OPE
Air having density p = 0.981 kg/m³ is flowing in a wind tunnel. A differential manometer connected to a pitot tube is used to measure the dynamic pressure of the air at the pitot tube location. The liquid in the manometer is oil having a specific gravity of 0.826, and the manometer reading is 76.2 mm. The wind tunnel is on the CU campus in Denver where g = 9.796 m/s?. a) Find the dynamic pressure of the air (answer: 615.8 Pa). b) Find the speed of the air at the pitot tube location (answer: 35.4 m/s). Air p = 0.981 kg/m³ h = 76.2 mm Oil, SG = 0.826
Consider a flow with a pressure and temperature of 2116 lb/ft2 and519 ◦R, respectively. A Pitot tube is inserted into this flow and measures apressure of 7712.8 lb/ft2. What is the velocity of this flow?
The dimensions of a duct system, supplying air at 20°C to two zones 5 and 6 are shown in Fig. The flow rates to the two zones are 1.4 m³/s and 1.0 m³/s respectively. The fan generates a total pressure of 285 kPa at the entrance section 1. Calculate (a) (i) the velocity pressures in the duct sections, (ii) (ii) the total pressures at all sections from 1 to 6. (b) If a damper is installed just upstream of section 5 to make the total pressures at 5 and 6 equal, calculate the required pressure loss through the damper. From L12 = 45m 2 3 L35 = 40m fan 1.4 m/s 2.4 m/s 4 D12 = 0.6 m L46 = 70m 6. D35 = 0.5 m D46 = 0.4 m 1.0 m/s Fig. El1.2.1 Supply air duct system