A 0.30 m X 0.40 m branch duct leaves a 0.30 m X 0.60 m main duct at an angle of 60°. The air temperature is 20°C. The dimensions of the main duct remain constant following branch. The flow rate upstream is 2.7 m3/s. Find the pressure downstream in the main duct if at 20°C, the mass per unit volume is 1.2041 kg/m

Q: As a process engineer, you are designing a new drinking water treatment plan using conventional…

A:

Q: 1. GUANZHO Bus Manufacturer install a ventilating fan in each bus with a suction duct diameter 0.315…

A: ● First determine the density of the air at the atmospheric pressure and the given air temperature.…

Q: Simulation of laminar gas flow in the pipe with Ansys Fluent Task: 1. Calculate velocity…

A:

Q: eter is A petroleum product is pumped at a rate of 2.32 x 10'm/s from a reservoir under atniospheric…

A: Given: The flow rate, Q = 2.32 x 10-3 m^3/s The height to be pumped, hd = 177 cm = 1.77 m The pump…

Q: Galvanized iron pipes with a roughness height of 0.40 cm are used to deliver water from reservoir A…

A:

Q: An oil with a dynamic viscosity of 0.8 Pa.s and specific gravity of 0.9 is flowing through a…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: pls replyyy Air is flowing through a square conduit whose section changes from 100 mm (section 1) to…

A: Please refer to the detailed solution given below,   Answer - Density of air at section 2 is 0.834…

Q: Non-dimensional entrence length for a round pipe flow depends on <(² Diameter of the pipe Length of…

A: The non-dimensional entrance length of pipe flow(internal flow) is effected according to the type of…

Q: The flow boundary layer in a diffuser with an angle of 30 degrees is detached from the wall surface,…

A: Option (a) pressure recovery  is the correct option

Q: A hydroelectric generation facility has a gross head of 120 m and a consistent yearlong water flow…

A:

Q: The pressure difference between two points in pipe due to turbulent flow depend on velocity,…

A: ∆P=fV,D,μ,ρ,ε,L

Q: You are designing a bioreactor that requires turbulent water flow (Re=2300) for better mixing of…

A: Given:Diameter,d=1.5 inches=1.539.37mWe know,For Reynold's number &gt;2300(in pipe flow),the flow is…

Q: Using excel how do you find the missing components and plot hf vs Re number

A: Given:L=6 ftD=34 in=3412ft=0.0625 ftFind:Need to complete the given table and graph of hf vs Re…

Q: A pipe is often used to assess the flow rate of water in the center of a pipe with an internal…

A:

Q: With the haze-pipe system in the figure, the ideal fluid (water) taken from the infinitely large…

A:

Q: Problem (3) Find the rate of change of h(t) (mm/s) if water is the fluid at all locations. Use V₁ =…

A: given data  V1 = 7.2 m/s  Q3= 1000L/min find the rate of change of h(t) in mm/sec

Q: 1. The figure shows a type of flushometer in which the flat vane rotates on a pivot as it deflects…

A: The term Flushometer is a meter that is mainly purposed in an inline handle to flush tankless…

Q: Water steam is running through the nozzle. Inlet pressure is P1=25 bars; T1=300C; V1=90m/s;…

A: a) Exit velocity 577.148 m/sb) Inlet diameter 0.5046 m    Outlet diameter 0.029 mExplanation:

Q: I need complete solution (step by step process) with given. Thanks Note: Instead of using g = 9.81…

A: Hl=1.39 mL=40 mf=0.012Q=600 L/s =0.6 m3/sg=9.806 m/s2

Q: Air at 68 degrees Celsius is being pumped through a pipe of internal diameter 6.4 inches. If the…

A: First calculate the Reynold number to identify wheather it is laminar or turbulent

Q: Two pipes of different diameters are joined together in series. The smaller pipe has a diameter of…

A:

Q: What is the friction factor (to three decimal places) of the flow of air (density 1.2 kg/m³,…

A:

Q: The mean volume flow rate in the femoral artery is 5 ml/s. The length of the femoral artery is 18 cm…

A: Given: Mean flow rate; Q =5 ml/s =5 *10-6 m3/s Length; L =18 cm =0.18 m Diameter; D =1cm =0.01 m…

Q: You are asked to calculate the pressure drop in a straight pipe. Air of density 1.225 kg/m³ is…

A: Pressure drop              ∆p=32μuL¯ρgd2=32×1.85×10-5×100×0.51.225×9.81×0.0252=3.94 Pa Coefficient…

Q: 3. Compute the friction head loss in meters of a fluid at a certain condition (S.G.-1.101) that is…

A:

Q: calculate the discharge.

A: Since you ave asked multiple questions, we will solve the first question for you. If you want any…

Q: 5. In this a fire fight system of ship water has speed N m/s. hose is in equilibrium Calculate the…

A:

Q: Glycerine, with a viscosity of 0.09 kg/ms and density of 1 260 kg/m³, is pumped at a flow rate of 20…

A:

Q: The power generated by the turbine shown is 7500 kW. Determine the outlet diameter and the mass flow…

A:

Q: Write the expanded form of Darcy’s Law. Draw a tube full of sand, with piezometers, and label the…

A: Darcy's law states about explains the flow of fluid through the porous medium like a rock. French…

Q: Consider steady flow of water in a situation where two pipe lines (pipe 1 and pipe 2) combine into…

A: GivenV1=1m/sA1=1m2V2=2m/sA2=2m2A3=2.5m2V3=?

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.