Q=2000JTout=?V(m/s) D=0.1mairAir at (2.95x10^2) K is entering in a circular pipe at 101325 Pa as shown in Figure. The velocity ofthe air at the pipe entrance is (1.5000x10^0) m/s. The diameter of the pipe is 0.1m. Specific gasconstant of air is 287 J/kg-K. Specific heat of air is 100O J/kg-K. Find the outlet temperature if 2000J of heat is added to the pipe.Answer should be in 'K' with three significant figures.Note: Your answer is assumed to be reduced to the highest power possible.Your Answer:Activate WindowsGo to Settings to activat(?9°CENG2020

Given Data: Heat added, Q=2000 J Specific heat, C=1000 J/kg-K

Q=2000J Tout=? V(m/s) D=0.1m air Air at (2.95x10^2) K is entering in a circular pipe at 101325 Pa as shown in Figure. The velocity of the air at the pipe entrance is (1.5000x10^0) m/s. The diameter of the pipe is 0.1m. Specific gas constant of air is 287 J/kg-K. Specific heat of air is 1000 J/kg-K. Find the outlet temperature if 2000 J of heat is added to the pipe. Answer should be in 'K' with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: Activate Windo Go to Settings to act

Q=2000J Tout=? V(m/s) D=0.1m air Air at (2.95x10^2) K is entering in a circular pipe at 101325 Pa as shown in Figure. The velocity of the air at the pipe entrance is (1.5000x10^0) m/s. The diameter of the pipe is 0.1m. Specific gas constant of air is 287 J/kg-K. Specific heat of air is 1000 J/kg-K. Find the outlet temperature if 2000 J of heat is added to the pipe. Answer should be in 'K' with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: Activate Windo Go to Settings to act

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The square-section duct in atmospheric conditions is exposed to air flow from outside as seen in the figure. Air temperature Tair=5°C velocity Vair= 10m/s. entering the canal at a flow rate of Mwater = 0.01 kg/s and a temperature of Twater = 50°C, Find the outlet temperature of the water. Geometric dimensions are given on the figure.
If the difference between the total pressure and static pressure in an air duct is measured by a pitot tube to be 6.5 cm H2O, what is the flow velocity in m/s? Density of water is 998 kg/m3, and g = 9.81 m/s2. 3 signififcant figures answer
Three immiscible fluids are contained in a tank: 1.0 m of water, 1.20 m of oil (s= 0.80), and air under a pressure of 16 kPa. The tank is closed and has a height of 3.0 m and a diameter of 1.0 m. Find the theoretical velocity through a 5 cm diameter orifice located 30 cm above the bottom of the tank. Answers: a. 8.03 m/s b.12.56 m/s c.15.8 m/s d.10.34 m/s
An ideal gas passes a diffuser. At the diffuser inlet, the temperature is T1 = 350.00 K, the pressure P1 = 100.00 kPa, the velocity V1 = 200.00 m/s, and the inlet area A1 = 0.30 m2. At the exit, the velocity is very small. The specific heat of the ideal gas at the constant pressure is cp = 1.0050 kJ/(kg·K). The gas constant is R = 0.2870 kPa·m3/(kg·K). Determine the mass flow rate __________(kg/s)
Question 3 Water (p = 1000 kg/m³, μ = 1.12 x 10-3 Ns/ m²) flows through a 0.01-m-diameter pipe at a velocity of 2 m/s. The length of the pipe is 40 m. A pump is used to maintain the flow from one reservoir to another reservoir as shown. The following data are available: KL elbow = 1.5, Kentrance = 0.5, Kexit = 1.0. Elbow Pump Elbow Figure Q1 Note that the entrance and exit are at the same elevation. The free surfaces of the reservoirs are also at the same elevation. (a) Calculate the total head losses in the pipe.
Air enters a duct (100 cm *10̟cm*10 cm) at 32°C at a rate of 0.28m /min to cool 138 W electronic component placed on the duct. Assuming 85 percent of the heat generated inside is transferred to air flowing through the duct and the remaining 15 percent is lost through the outer surfaces of the duct. What is the exit temperature of air (°C)? C,= 1007 J/kg.°C, v =1.654×10-S m²/s, p 1.146 kg/m Pr = 0.7268, k = 0.02625 W/m.°C Select one or more:
Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps please
Air flows from a 10cm pipe in which the temperature and pressure are 4-C and 280kpa, respectively, into a 5cm pipe in which the pressure is 147kpa gage. Calculate the velocity and discharge in each pipe, assuming isothermal conditions, standard atmospheric pressure and no losses. The gas constant for air is 280N-m/kg-K.
200 pm 0.12 cm Fluid Stationary cylinder 4 In regions far from the entrance, fluid flow through a circular pipe is one-dimensional, and the velocity profile for laminar flow is given by u(r) = Umax(1 - r/R9), where R is radius of the pipe, r is the radial distance from the center of the pipe, and Umax is the maximum flow velocity, which occurs at the center. Obtain (a) a relation for the drag force applied by the fluid on a section of the pipe length L and (b) the value of the drag force for water flow at 20°C with R = 0.08 m, L = 15 m, Umax = 3 m/s, and u = 0.0010 kg/m.s. %3D
Air at (2.9000x10^2) K is entering in a circular pipe at 101325 Pa as shown in Figure. The velocity of the air at the pipe entrance is (1.00x10^0) m/s. The diameter of the pipe is 0.1m. Specific gas constant of air is 287 J/kg-K. Specific heat of air is 1000 J/kg-K. Find the outlet temperature if 2000 J of heat is added to the pipe.
We have a tank (large enough to neglect the velocity of the fluid surface in the tank v1 =0). The tank contains water at a mevel of 15 meters. The tank is enclosed and the air space above the water is at 5 atm. The exit of the tank consists of 25 meters of 2 cm diamter pipe with d/D = 0.0004. It exhaust to the atmospere at 1 atm. What is the exit velocity?
An ideal gas passes a diffuser. At the diffuser inlet, the temperature is T1 = 350.00 K, the pressure P1 = 100.00 kPa, the velocity V1 = 200.00 m/s, and the inlet area A1 = 0.30 m2. At the exit, the velocity is very small. The specific heat of the ideal gas at the constant pressure is cp = 1.0050 kJ/(kg·K). The gas constant is R = 0.2870 kPa·m3/(kg·K). Determine the enthalpy per unit mass at the exit, h2__________(kJ/kg)