Heated air at 1 atm and 35°C is to be transported in a 150-m-long circular plastic duct at a rate of 0.35 m³/s (Fig. 1). If the head loss in the pipe is not to exceed 20 m, using the Colebrook equation and consulting with the FE Reference Handbook and appropriate table(s) for equations and properties. Write a Matlab code to determine the i. ii. minimum diameter of the duct, the friction factor, iii. average flow velocity and iv. Reynolds number of the flow

Heated air at 1 atm and 35°C is to be transported in a 150-m-long circular plastic duct at a rate of 0.35 m³/s (Fig. 1). If the head loss in the pipe is not to exceed 20 m, using the Colebrook equation and consulting with the FE Reference Handbook and appropriate table(s) for equations and properties. Write a Matlab code to determine the i. ii. minimum diameter of the duct, the friction factor, iii. average flow velocity and iv. Reynolds number of the flow

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q.5 A pump circulates water through a closed pipe network connecting a water heater and a heating coil (heat exchanger) in a room. The total length of the pipe is 28 m and the diameter is 32 mm. There are six 90°-elbows and a globe valve in the network. The head loss through the water heater and the heating coil are 1.6 m and 1.2 m respectively. The water flow rate is 0.88 Ls!. The system uses schedule-40 steel pipes with threaded fittings. Calculate the (i) flow velocity and the unit pressure loss in the pipe. (ii) increase in head across the pump. (iii) power input to the pump if the efficiency of the pump is 70%.
7. Using the velocity distribution for a laminar, incompressible flow of a Newtonian fluid in a long vertical tube, for a fluid whose density is 300 kg per cubic meter and viscosity is 1x10 - 4 Pascal-second travelling along a long circular tube of cross sectional area of 1 cm2 owing to a pressure gradient of 1,000 Pascal per meter, the average velocity in meter per second (m/s) is Please help asap
"Engine oil at 40 C [density 876 kg/m^3, viscosity 0.2177 kg/m.s] flows in a 22-cm-diameter pipe at a velocity of 1.5 m/s. The head loss (in meters) of oil for a pipe length of 140 m is ?
Liquid biofuel (density= 789 kg/m3) is being pumped from a storage tank through a pipe with 1-inch innerdiameter (ID). The fuel is being pumped at a rate of 3.00 gallons per minute. In this process, what is thekinetic energy transport rate (Ėk) in units of horsepower (hp) and ft•lbf/sec.
The characteristics of a centrifugal pump operating at 1000 rpm is given by H=45-21002. The system characteristics may be represented by H = 28+3200². The units for volume flow rate Q and head H are m³/s and m, respectively. Assume the validity of the pump similarity laws. When one pump operating at 2000 rpm is used, with the system characteristics remaining unchanged, the operating volume flow rate is m³/s.
Solve it correctly please. I will rate accordingly.
7-8
Experiment Data Take the following data for the syringe injection pump 2/ Inner diameter of syringe barrel: D = 1.5 cm Inner diameter of the needle shaft of the syringe: d = 0.5 mm The thread pitch of lead screw: pt = 0.75 mm Lead screw rotation velocity (rpm): n Calculations a Liquid injection rate (cm³/hr) Q = pt*n* 60 * π * D²/4 Velocity of liquid in syringe barrel (cm/min) vb = 40/ (60** D²) Velocity of liquid in syringe needle (cm/min) v₁ = 40/ (60*n* d²) b Find the rotation velocity of lead screw n and the velocity of liquid in syringe needle if the required injection dose is 1. 10 cm³ in 3 hours (continuous injection) 2. 20 cm³ in 12 hours (discontinuous injection, 5 cm³ each 3 hour, injection time = 1 min). Discus the recl Solution Calculate the liquid injection rate Q = P₁ xnx60xD² = 0.075xnx60××1.5² = 7.94n- cm³ hr Calculate the velocity of liquid in barrel V₁ == 40 60xπx D² 4x7.94n 60xx1.5² = 0.07ncm hr Calculate the velocity of liquid in needle 40 60xxxd2 4x7.94n 60xπx…
Water at 60°F (p = 62.36 lbm/ft³ and µ = 7.536 × 104 lbm/ft.s) is flowing steadily in a 2- in-diameter horizontal pipe made of stainless steel at a rate of 0.2 ft³/s (Fig. 2). Use the Colebrook equation and consult the FE Reference Handbook and appropriate table(s) for equations and properties. Write a Matlab code to determine the i. ii. iii. pressure drop, the head loss, and the required pumping power input for flow over a 200-ft-long section of the pipe. 2 in 0.2 ft³/s water -200 ft-
Topic: Heat transfer Completely solve and box the final answer. Water flows at 5m/s is passed through a tube of 2.5 cm diameter, it is found to be heated from 20degC to 60degC. The heating is achieved by condensing steam on the surface of the tube and subsequently the surface temperature of the tube is maintained at 90degC. Water properties are as follows: density=995kg/m3, kinematic viscosity=.657x10-6 m2/s, Pr=4.43, k=.628W/mK, cp=4178J/kgK. Determine the Reynolds number.
A pitot-static tube to be used in 2n airplane for on-flight measurement was calibrated on ground by using air of density 1.20 kg/m? . A measurement taken at an altitude of 3000 m where the ambient pressure and density were 70 kPa (abs) and 0.91 kg/m? respectively, indicated a velocity of 200 m/s by using the above ‘ground level calibration. Estimate the true speed of the airplane [Take k = 1.4 2nd R = 287 J(kg K
NOTE: USE CANCELLATION OF UNITS PICTURE 2 REFERENCE FOR CONVERSION OF UNITS